IP137AHVK Просмотр технического описания (PDF) - Semelab - > TT Electronics plc
Номер в каталоге
Компоненты Описание
производитель
IP137AHVK Datasheet PDF : 4 Pages
| |||
IP137A SERIES
IP137A SERIES
IP337A SERIES
IP337A SERIES
LM137A SERIES
LM137A SERIES
Parameter
Test Conditions
VREF Reference Voltage
∆VOUT Line Regulation 1
∆IOUT
∆VOUT Load Regulation 1
∆IOUT
Thermal Regulation
IOUT = 10mA
IOUT =10mA to IMAX TJ = -55 to 150°C
VIN – VOUT = 3V to VMAX P ≤ PMAX
VIN – VOUT = 3V to VMAX
TJ = -55 to 150°C
IOUT = 10mA to IMAX
VOUT ≤ 5V
VOUT ≥ 5V
IOUT = 10mA to IMAX
VOUT ≤ 5V
TJ = -55 to 150°C
VOUT ≥ 5V
tp = 10ms
TA = 25°C
LCC4 Package
Ripple Rejection
IADJ Adjust Pin Current
∆IADJ Adjust Pin Current
Change
VOUT = -10V
f = 120Hz
CADJ = 0
CADJ = 10µF
TJ = -55 to 150°C
TJ = -55 to 150°C
IOUT = 10mA to IMAX
TJ = -55
VIN – VOUT = 3V to 40V
to 150°C
VIN – VOUT = 3V to 50V
(HV SERIES)
IMIN Minimum Load
Current
ICL
Current Limit
TJ = -55 to 150°C
TJ = -55 to 150°C
VIN – VOUT ≤ 40V
VIN – VOUT ≤ 10V
VIN – VOUT ≤ 15V
VIN – VOUT = 40V
VIN – VOUT = 50V
(HV SERIES)
∆VOUT Temperature
∆TEMP Stability
TJ = -55 to 150°C
∆VOUT Long Term Stability TA = +125°C
∆TIME
t = 1000 Hrs
en
RθJC
RMS Output Noise f = 10 Hz to 10 kHz
(% of VOUT)
Thermal Resistance
Junction to Case
TA = 25°C
K Package
R Package
G Package
LCC4 Package
IP137A , IP137AHV
LM137A , LM137AHV
Min. Typ. Max.
-1.238 -1.25 -1.262
-1.220
60
-1.25
0.005
0.010
5
0.1
10
0.2
0.002
66
-1.280
0.010
0.030
25
0.5
50
1
0.020
0.040
70
80
65
100
0.2
2
1.0
5
2.0
6
2.5
5
1.2
3
1.5
2.2
3.2
0.24 0.4
1
0.2
0.4
0.8
0.6
1.5
0.3
1
0.003
2.3
3
5
7
3
5
13
IP137 , IP137HV
LM137 , LM137HV
Min. Typ. Max.
-1.225 -1.25 -1.275
Units
V
-1.200
-1.250
0.010
0.020
15
0.3
20
0.3
0.002
60
-1.300
0.020
0.050
25
0.5
50
1
0.02
0.040
V
%/V
mV
%
mV
%
%/W
dB
66
77
dB
65
100 µA
0.5
5
2
5
µA
3
6
2.5
1.2
1.5
2.2
0.24 0.4
0.2
0.4
5
mA
3
3.2
A
0.8
0.6
%
0.3
1
%
0.003
2.3
5
3
%
3
7
°C/W
5
13
1) Regulation is measured at constant junction temperature, using pulse testing at a low duty cycle. Changes in output voltage due to heating effects are covered under
thermal regulation specifications. Load regulation is measured at a point 1/8” from the bottom of the package for the TO–3 and TO–66 packages, at the junction of the
wide and narrow portion of the output lead for the SMD packages, and 1/8” below the base of the package on the output pin of the TO–257 package.
2) Test Conditions unless otherwise stated: VIN – VOUT = 5V , IOUT = 0.5A , PMAX = 20W , IMAX = 1.5A, VMAX = 40V for standard series , 50V for HV series.
Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed
to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use.
Semelab encourages customers to verify that datasheets are current before placing orders.
Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk
Document Number 2831
Issue 3
Share Link: 