IR2114SSPBF Просмотр технического описания (PDF) - Infineon Technologies
Номер в каталоге
Компоненты Описание
производитель
IR2114SSPBF Datasheet PDF : 33 Pages
| |||
IR2114/IR2214SSPbF
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage
parameters are absolute voltages referenced to VSS, all currents are defined positive into any lead The thermal resistance
and power dissipation ratings are measured under board mounted and still air conditions.
Symbol
Definition
Min.
Max. Units
VS
VB
VHO
VCC
COM
VLO
VIN
VFLT
VDSH
VDSL
dVs/dt
High side offset voltage
High side floating supply voltage
IR2114
IR2214
High side floating output voltage (HOP, HON and SSDH)
Low side and logic fixed supply voltage
Power ground
Low side output voltage (LOP, LON and SSDL)
Logic input voltage (HIN, LIN and FLT_CLR)
Fault input/output voltage (FAULT/SD and SY_FLT)
High side DS input voltage
Low side DS input voltage
Allowable offset voltage slew rate
VB - 25
-0.3
-0.3
VS - 0.3
-0.3
VCC - 25
VCOM -0.3
-0.3
-0.3
VS -3
VCOM -3
—
VB + 0.3
625
1225
VB + 0.3
25
VCC + 0.3
VCC + 0.3
VCC + 0.3
VCC + 0.3
VB + 0.3
VCC + 0.3
50
V
V/ns
PD
RthJA
TJ
TS
TL
Package power dissipation @ TA ≤ 25 °C
Thermal resistance, junction to ambient
Junction temperature
Storage temperature
Lead temperature (soldering, 10 seconds)
—
1.5
W
—
65 °C/W
—
150
-55
150
°C
—
300
Recommended Operating Conditions
For proper operation the device should be used within the recommended conditions. All voltage parameters are absolute
voltages referenced to VSS. The VS offset rating is tested with all supplies biased at a 15 V differential.
Symbol
Definition
Min.
Max. Units
VB
VS
VHO
VLO
VCC
COM
High side floating supply voltage †
High side floating supply offset voltage ††
High side output voltage (HOP, HON and SSDH)
Low side output voltage (LOP, LON and SSDL)
Low side and logic fixed supply voltage (Note 1)
Power ground
IR2114
IR2214
VS + 11.5 VS + 20
VSS
600
VSS
1200
VS
VS + 20
VCOM
VCC
11.5
20
V
-5
5
VIN
Logic input voltage (HIN, LIN and FLT_CLR)
VSS
VCC
VFLT
Fault input/output voltage (FAULT/SD and SY_FLT)
VSS
VCC
VDSH
VDSL
tPWHIN
High side DS pin input voltage
Low side DS pin input voltage
High side pulse width for HIN input
VS - 2.0
VB
VCOM - 2.0
VCC
1
µs
TA
Ambient temperature
-40
125 °C
†
While internal circuitry is operational below the indicated supply voltages, the UV lockout disables the output
drivers if the UV thresholds are not reached. A minimum supply voltage of 8V is recommended for the driver
to operate safely under switching conditions at VS pin (please refer to the “start-up sequence” in application
section of this document)
††
Logic operational for VS from VSS-5 V to VSS +600 V or 1200 V. Logic state held for VS from VSS -5 V to VSS-
VBS. For a negative spike on VB (referenced to VSS) of less than 200ns the IC will withstand a sustained peak
of -40V under normal operation and an isolated event of up to -70V peak spike (please refer to the Design
Tip DT97-3 for more details).
www.irf.com
© 2009 International Rectifier
2
Share Link: 