SF2183E Просмотр технического описания (PDF) - Murata Manufacturing
Номер в каталоге
Компоненты Описание
производитель
SF2183E Datasheet PDF : 4 Pages
| |||
SF2183E
• Low-low UHF SAW Filter
• Surface-mount 3.0 x 3.0 mm Package
• Complies with Directive 2002/95/EC (RoHS) Pb
Absolute Maximum Ratings
400.00 MHz
SAW Filter
Rating
Input Power Level
DC Voltage on any Non-ground Terminal
Operating Temperature Range
Component Storage Temperature Range
Storage Temperature Range in Tape and Reel
Maximum Soldering Profile, 5 cycles/ 10 seconds maximum
Electrical Characteristics
Value
10
6
-40 to +85
-40 to +125
-40 to +85
265
Units
dBm
V
°C
°C
°C
°C
SM3030-6
Characteristic
Center Frequency
Minimum Insertion Loss
Passband Attenuation Relative to ILMIN, 399.875 to 400.125 MHz
Stopband Attenuation Referenced to ILMIN:
10.0 to 370.0 MHz
370.0 to 390.0 MHz
390.0 to 398.8 MHz
401.0 to 409.0 MHz
409.0 to 414.0 MHz
414.0 to 800.0 MHz
800.0 to 2500.0 MHz
Input Impedance
Output Impedance
Case Style
Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator
Standard Reel Quantity
Reel Size 7 Inch
Reel Size 13 Inch
Electrical Connections
Connection
Terminals
Input
2
Output
5
Case Ground
All others
Sym
Notes
Min
Typ
Max
fC
ILMIN
400.00
3.0
4.0
0.7
3.0
50
56
42
46
22
25
10
22
30
40
42
50
45
55
ZS
865 || 2 pF
ZL
865 || 2 pF
SM3030-6 3.0 x 3.0 mm Nominal Footprint
871, YWWS
500 Pieces/Reel
3000 Pieces/Reel
O u tp u t
5 0 o h m M a tc h in g N e tw o r k
73 nH
6 .8 p F
6
1
5
2
4
3
73 nH
6 .8 p F
In p u t
Units
MHz
dB
dB
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
S F2183E
(b o tto m v ie w )
NOTES:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to
50 and measured with 50 network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance
matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that
the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd.
Copyright © Murata Manufacturing Co., Ltd. All Rights Reserved 2015
SF2183E (R) 8/19/16
Page 1 of 4
www.murata.com
Share Link: 