HIP6301V Просмотр технического описания (PDF) - Renesas Electronics
Номер в каталоге
Компоненты Описание
производитель
HIP6301V Datasheet PDF : 20 Pages
| |||
HIP6301V, HIP6302V
Absolute Maximum Ratings
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+7V
Input, Output, or I/O Voltage . . . . . . . . . . GND -0.3V to VCC + 0.3V
Recommended Operating Conditions
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V ±5%
Ambient Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
Thermal Information
Thermal Resistance (Typical, Note 1)
JA (°C/W)
16 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . .
70
20 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . .
65
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty..
NOTES:
1. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. (See Tech Brief TB379 for details.)
2. VID input levels above 2.9V may produce an reference-voltage offset inaccuracy.
3. Parts are 100% tested at +25°C. Temperature limits established by characterization and are not production tested.
Electrical Specifications
PARAMETER
Operating Conditions: VCC = 5V, TA = +0°C to +70°C, Unless Otherwise Specified.
TEST CONDITIONS
MIN
(Note 3) TYP
MAX
(Note 3) UNITS
INPUT SUPPLY POWER
Input Supply Current
POR (Power-On Reset) Threshold
REFERENCE AND DAC
RT = 100k
VCC Rising
VCC Falling
-
-
15
mA
4.25 4.38 4.5
V
3.75 3.88 4.00
V
System Accuracy
Percent system deviation from programmed VID Codes
-0.8
-
0.8
%
DAC (VID0 - VID3) Input Low Voltage DAC Programming Input Low Threshold Voltage
-
-
0.8
V
DAC (VID0 - VID3) Input High Voltage DAC Programming Input High Threshold Voltage
2.0
-
-
V
VID Pull-Up
VIDx = 0V or VIDx = 2.5V (Note 2); Not tested - for reference only 10
-
40
µA
CHANNEL GENERATOR
Frequency, FSW
Disable Voltage
ERROR AMPLIFIER
RT = 100k, ±1%
VFS/DIS to disable controller; Not tested - for reference, only
224
280 336
kHz
-
-
1.0
V
DC Gain
Gain-Bandwidth Product
Slew Rate
Maximum Output Voltage
Minimum Output Voltage
ISEN
Full-Scale Current Level
RL = 10k to ground
CL = 100pF, RL = 10k to ground
CL = 100pF, RL = 10k to ground
RL = 10k to ground
RL = 10k to ground
Not tested - for reference, only
-
72
-
dB
-
18
-
MHz
-
5.3
-
V/µs
3.6
-
-
V
-
-
0.5
V
-
50
-
µA
Overcurrent Trip Level
Not tested - for reference, only
-
82.5
-
µA
POWER-GOOD MONITOR
Undervoltage Threshold
Undervoltage Threshold
PGOOD Low Output Voltage
PROTECTION
VSEN Rising
VSEN Falling
IPGOOD = 4mA
-
0.92
-
VDAC
-
0.90
-
VDAC
-
-
0.4
V
Overvoltage Threshold
Overvoltage Hysteresis
VSEN Rising
VSEN Falling; Not tested - for reference, only
1.12 1.15 1.20 VDAC
-
2
-
%
FN9034 Rev 3.00
May 5, 2008
Page 7 of 20
Share Link: 