HI-506A Просмотр технического описания (PDF) - Renesas Electronics
Номер в каталоге
Компоненты Описание
производитель
HI-506A Datasheet PDF : 20 Pages
| |||
HI-506A, HI-507A, HI-508A, HI-509A
Electrical Specifications Supplies = +15V, -15V; VREF Pin = Open; VAH (Logic Level High) = 4V; VAL (Logic Level Low) = 0.8V,
Unless Otherwise Specified. For Test Conditions, Consult Test Circuits Section. (Continued)
-2, -8
-5
PARAMETER
TEST
TEMP
MIN
MAX
MIN
MAX
CONDITIONS (°C) (Note 12) TYP (Note 12) (Note 12) TYP (Note 12) UNITS
Input Leakage Current (High or Low), IA
Notes 4, 8
Full
MOS Drive, VAL, HI-506A/HI-507A
VREF = +10V
25
MOS Drive, VAH, HI-506A/HI-507A
VREF = +10V
25
ANALOG CHANNEL CHARACTERISTICS
-
-
1.0
-
-
0.8
6.0
-
-
-
-
1.0
A
-
-
0.8
V
6.0
-
-
V
Analog Signal Range, VIN
On Resistance, rON
Note 4
Notes 4, 5
Full
-15
-
+15
-15
-
+15
V
25
-
1.2
1.5
-
1.5
1.8
k
Full
-
1.5
1.8
-
1.8
2.0
k
Off Input Leakage Current, IS(OFF)
Notes 4, 6
25
-
0.03
-
Full
-
-
50
-
0.03
-
nA
-
-
50
nA
Off Output Leakage Current, ID(OFF)
HI-506A
Notes 4, 6
25
-
0.1
-
-
0.1
-
nA
Full
-
-
300
-
-
300
nA
HI-507A
Full
-
-
200
-
-
200
nA
HI-508A
Full
-
-
200
-
-
200
nA
HI-509A
Full
-
-
100
-
-
100
nA
ID(OFF) With Input Overvoltage Applied
Note 7
25
-
4.0
-
Full
-
-
2.0
-
4.0
-
nA
-
-
-
A
On Channel Leakage Current, ID(ON)
HI-506A
Notes 4, 6
25
-
0.1
-
-
0.1
-
nA
Full
-
-
300
-
-
300
nA
HI-507A
Full
-
-
200
-
-
200
nA
HI-508A
Full
-
-
200
-
-
200
nA
HI-509A
Full
-
-
100
-
-
100
nA
Differential Off Output Leakage Current, IDIFF,
(HI-507A, HI-509A Only)
Full
-
-
50
-
-
50
nA
POWER SUPPLY CHARACTERISTICS
Current, I+
Notes 4, 10
Full
-
0.5
2.0
-
0.5
2.0
mA
Current, I-
Notes 4, 10
Full
-
0.02 1.0
-
0.02 1.0
mA
Power Dissipation, PD
Full
-
7.5
-
-
7.5
-
mW
NOTES:
4. 100% tested for Dash 8. Leakage currents not tested at -55°C.
5. VOUT = 10V, IOUT = +100A.
6. 10nA is the practical lower limit for high speed measurement in the production test environment.
7. Analog Overvoltage = 33V.
8. Digital input leakage is primarily due to the clamp diodes (see Schematic). Typical leakage is less than 1nA at +25°C.
9. VEN = 0.8V, RL = 1k, CL = 15pF, VS = 7VRMS, f = 100kHz.
10. VEN, VA = 0V or 4V.
11. To drive from DTL/TTL Circuits, 1k pull-up resistors to +5V supply are recommended.
12. Parts are 100% tested at +25°C. Over-temperature limits established by characterization and are not production tested.
FN3143 Rev.6.00
October 30, 2007
Page 9 of 20
Share Link: 