LTC1550L Просмотр технического описания (PDF) - Linear Technology

Номер в каталоге

Компоненты Описание

производитель

LTC1550L

Low Noise, Switched Capacitor Regulated Voltage Inverters

Linear Technology 

LTC1550L/LTC1551L

PIN FUNCTIONS

SHDN: Shutdown (TTL Compatible). This pin is active low

(SHDN) for the LTC1550L and active high (SHDN) for the

LTC1551L. When this pin is at VCC (GND for LTC1551L),

the LTC1550L operates normally. When SHDN is pulled

low (SHDN pulled high for LTC1551L), the LTC1550L

enters shutdown mode. In shutdown, the charge pump

stops, the output collapses to 0V, and the quiescent

current drops typically to 0.2µA. The SHDN pin for the

LTC1550L is a high impedance input and has no internal

pull-up. The user must supply a resistor or current source

pull-up to default the LTC1550L into normal operation.

The SHDN pin for the LTC1551L has an internal 5µA

typical pull-down that defaults the LTC1551L into normal

operation.

VCC: Power Supply. VCC requires an input voltage between

2.7V and 5.25V. Certain combinations of output voltage

and output load current may place additional restrictions

on the required input voltage. Consult the Electrical Char-

acteristics table and Typical Performance Characteristics

for guaranteed test points. The difference between the

input voltage and output should not exceed 10.5V or

damage to the chip may occur. VCC must be bypassed

directly to PGND (GND for 8-pin packages) with at least a

0.1µF capacitor placed in close proximity to the chip. A 1µF

or larger low ESR bypass capacitor is recommended to

minimize noise and ripple at the output. A surface mount

ceramic capacitor is recommended.

C1+: C1 Positive Input. Connect a 0.1µF capacitor between

C1+ and C1–.

VOUT: Negative Voltage Output. This pin must be bypassed

with a 4.7µF or larger capacitor to ensure regulator loop

stability. LTC recommends at least 10µF to achieve the

specified output ripple. The output capacitor should be a

moderate ESR capacitor, and not a very low ESR capaci-

tor, as the zero in the feedback loop (formed by the ESR

and the output capacitor) provides phase lead to the linear

regulator feedback loop. Using very low ESR output ca-

pacitors will result in the output oscillating. A low ESR

0.1µF capacitor is recommended in parallel with the main

output capacitor to minimize high frequency spikes at the

output. The ground connection for the output capacitor

should connect directly to the VCC and CPOUT bypass

capacitors, as well as to the GND of the LTC1550L/

LTC1551L. LTC recommends a separate trace for the VOUT

capacitor ground connection to minimize noise.

C1–: C1 Negative Input. Connect a 0.1µF capacitor from

C1+ to C1–.

GND: Ground. Connect to a low impedance ground. A

ground plane will help minimize regulation errors.

CPOUT: Negative Charge Pump Output. This pin requires a

0.1µF storage capacitor to ground. In order to achieve

ripple on the output voltage of less than 1mV, the ground

connection for the CPOUT capacitor must tie directly to the

bottom of the VCC bypass capacitor and at the GND pin of

the LTC1550L/LTC1551L. This minimizes the AC current

path for the charge pump.

REG: This is an open-drain output that pulls low when the

output voltage is within 5% of the set value. It will sink 4mA

to ground with a 5V supply. The external circuitry must

provide a pull-up or REG will not swing high. The voltage

at REG may exceed VCC and can be pulled up to 6V above

ground without damage. For the LTC1550L adjustable

voltage version, the REG pin is only available in the 16-lead

GN package.

ADJ (for adjustable versions): This is the feedback point

for the external resistor divider string. Connect a divider

string from GND to VOUT with the divided tap connected to

ADJ. Note that the resistor string needs to be connected

“upside-down” from a negative regulator. See the Applica-

tions Information section for hook-up details.

GN PACKAGE ONLY

PGND: Power Ground. Connect to a low impedance ground.

PGND should be connected to the same potential as

AGND.

AGND: Analog Ground. Connect to a low impedance

ground. AGND should be connected to a ground plane to

minimize regulation errors.

NC: No Internal Connection.

6

Share Link: