AA5001 Просмотр технического описания (PDF) - Unspecified

Номер в каталоге

Компоненты Описание

производитель

AA5001

Programmable Audio Test System

Unspecified 

TM 500 / 5000

MODULAR TEST INSTRUMENTS

IEEE-4888 Commands

There are more than 140 total programming

commands in the complete command sets for

the SG 5010 and AA 5001. A few examples

are shown below. While the full form of the

commands shown is quite acceptable and will

be operated upon by the instruments, it is

also possible to truncate any command down

to as little as the characters shown in bold

face. Each programmer may thus choose the

best compromise between program

readability and minimum bus traffic.

SG 5010

FUnction SIne Selects sine wave

FUnction SQuare Selects square wave

FUnction?

Query; instrument

responds with present

function

AMPlitude < num > Sets amplitude

DBm <num>

Sets amplitude in dBm

VPp < num > Sets amplitude in volts

peak-to peak

VRms < num > Sets amplitude in volts

rms

FRequency <num> Sets frequency

IMfreq < num > Sets SMPTE, DIN, or

CCIF offset IM

frequency

ONCycles < num > Sets number of ON

cycles for burst mode

STARTFreq <num>Sets starting frequency

for sweep operation

STOPVolts < num >Sets stop rms volts for

amplitude sweep

operation

NSteps < num > Sets number of steps

from start to stop for

sweep operation

STEptime < num > Sets time per sweep

step

BAlance

Sets output to

balanced mode

UNbalance

Sets output to

unbalanced mode

FLoat or FLt

Sets output floating

GRound or GNd Connects output center

tap (balanced) or low

side (if unbalanced) to

ground

AA 5001

FUnc THDPct

FUnc THDDb

FUnc DBm

SENd

DUs ON

Points < num >

TOl <num>

Counts <num>

REsp AVG

FIlt HP

FIlt Wtg

FIlt EXt

FPset

SETings

ERR

Sets THD mode percent

Sets THD mode, dB

Sets level mode, dBm

Returns a reading

Tells SEND command

to delay until reading

is settled per setting

algorithm

Sets number of

points,1 to 6, which

must be within settling

algorithm “window”

before reading is

returned

Sets tolerance “window”

in percent

Sets ± counts term of

settling algorithm

Selects AVG detector

Enables high-pass filter

Enables weighting filter

Enables external filter

Sets instrument to front

panel settings even

though under remote

control

Query, returns all

programmable settings

Query, returns code for

most recent error

reported in serial poll

Ordering Information

AA 5001

Prgm. Distortion Analyzer

AA 5001/CCIR AA 5001 w/CCIR/DIN

SG 5010

Prgm. Oscillator

TM 5003

TM 5003/RI

3 Wide Power Module

Mainframe, GPIB

TM 5003 w/Rear Interface

TM 5006A 6 Wide Power Module

Mainframe, GPIB

TM 5006A/R TM 5006A w/Rack Mount

TM 5006A/RI TM 5006A w/Rear Interface

TM 5006A/R/RI TM 5006A w/Rack Mt &

Rear Interface

TM 5006A/EMC TM 5006A w/EMC Shielding

Mainframe Power Plug Options

Standard

UE220

UK240

A240

NA240

S220

120V North American

220V Universal Euro

& Switzerland

240V United Kingdom

240V Australian

240V North American

220V Switzerland

Warranty

One year on materials and workmanship.

Calibration Documentation

Contact TEGAM for OPTION Z540 NIST

Traceable Compliance Certificate and Test Data.

Calibration & Technical Services

For warranty and remedial repair, calibration

services and spare parts, or for additional

information on TEGAM sales and service

offices around the world, contact us at

440-466-6100 (ph) or 440-466-6110 (fx).

SG5010.991PG

THE GLOB AL SOURCE FOR PROVEN TEST

AND MEASUREMENT TECHNOLOGY.

TEN TEGAM WAY • GENEVA, OHIO 44041

440-466-6100 • FAX 440-466-6110

www.tegam.com • e-mail: sales@tegam.com

Share Link: