AGN20003X Просмотр технического описания (PDF) - Matsushita Electric Works

Номер в каталоге

Компоненты Описание

производитель

AGN20003X

GN-RELAYS ULTRA-SMALL PACKAGE SLIM POLARIZED RELAY

Matsushita Electric Works 

GN

NOTES

1. Coil operating power

1) As a general rule, only a pure DC pow-

er supply should be used for the coil drive.

2) To ensure proper operation, the voltage

applied to both terminals of the coil should

be ±5% (at 20°C 68°F) the rated operating

voltage of the coil. Also, be aware that the

pick-up and drop-out voltages will fluctu-

ate depending on the ambient tempera-

ture and operating conditions.

3) The ripple factor for the voltage applied

to the coil should be less than 5%.

4) For set and reset latching relays, the

rated operating voltage should be applied

to the coil for 10 ms or more.

2. Coil connection

When connecting coils, refer to the wiring

diagram to prevent mis-operation or mal-

function.

3. External magnetic field

Since GN relays are highly sensitive po-

larized relays, their characteristics will be

affected by a strong external magnetic

field. Avoid using the relay under that con-

ditions.

4. Cleaning

In automatic cleaning, cleaning with the

boiling method is recommended. Avoid ul-

trasonic cleaning which subjects the relay

to high frequency vibrations. It may cause

the contacts to stick.

lt is recommended that a fluorinated hy-

drocarbon or other alcoholic solvent be

used.

5. Packing style

1) The relay is packed in a tube with the

relay orientation mark on the left side, as

shown in the figure below.

Orientation (indicates PIN No.1)stripe

Stopper (green)

Stopper (red)

2) Tape and reel packing

(A type)

(1)-1 Tape dimensions

mm inch

Relay polarity bar

(Z type)

0.40

1.50

+0.1

0

dia

.059

+.004

0

dia

.016

4.00

.157

2.00

.079

11.50

.453

1.75

.069

24.00±0.3

11.10 .945±.012

.437

10.70±0.2

.421±.008

GN relays

2.00dia

.079dia

16.00

8.00

.630

.315

Tape coming out direction

General tolerance ±0.1 mm .004 inch

(S type)

(1)-2 Tape dimensions

Relay polarity bar

(Z type)

2.00

1.50

+0.1

0

dia

.079

.059

+.004

0

dia

4.00 2.0dia

.157 .079dia

1.75

.069

10.70±0.2

.421±.008

0.40

.016

11.50

.453 24.00±0.3

11.10 .945±.012

.437

GN relays

16.00

6.3

.630

.248

Tape coming out direction

General tolerance ±0.1 mm .004 inch

(2) Dimensions of plastic peel

mm inch

21±0.8 dia.

.827±.031 dia.

2.0±0.5

.079±.020

100±1 dia.

3.937±.039 dia.

370±2 dia.

14.567±.079 dia.

13±0.2 dia.

.512±.008 dia.

24.4

+2

0

.961

+.079

0

2.0±0.2

.079±.008

6. Automatic insertion

To maintain the internal function of the

relay, the chucking pressure should not

exceed the values below.

Chucking pressure in the direction A:

4.9 N {500gf} or less

Chucking pressure in the direction B:

9.8 N {1 kgf} or less

Chucking pressure in the direction C:

9.8 N {1 kgf} or less

,,,C

A

B

Please chuck the portion.

Avoid chucking the center of the relay.

In addition, excessive chucking pressure

to the pinpoint of the relay should be

avoided.

For Cautions for Use, see Relay Technical Information (Page 48 to 76).

91/12/82000

All Rights Reserved, © Copyright Matsushita Electric Works, Ltd.

Go To Online Catalog

Share Link: