S2EB-12V Просмотр технического описания (PDF) - Matsushita Electric Works
Номер в каталоге
Компоненты Описание
производитель
S2EB-12V Datasheet PDF : 4 Pages
| |||
S
ACCESSORIES
S Relay Socket,
S-PS
Specifications
Breakdown voltage
1,500 Vrms between terminals
Insulation resistance
Heat resistance
Maximum continuous current
More than 100 MΩ between terminals at 500 V DC Mega
150 ±3°C (302 ±5.4°F) for 1 hour.
4A
(Note: Don't insert or remove relays while in the energized condition.)
Dimensions
12.4±0.6
.488±.024
18.3±0.6
.720±.024
1.2±0.3
.047±.012
4.85±0.3
.191±.012
1.5±0.3
.059±.012
5.08±0.3
.200±.012
32.4±0.6
1.276±.024
15.5±0.6
.610±.024
0.4±0.1
.016±.004
1.5±0.3
.059±.012
7.62±0.3
.300±.012
3.4±0.3
.134±.012
Terminal width: 1.3 .051
Terminal thickness: 1.2 .047
PC board pattern (Copper-side view)
7.6
.299
5.08 5.08 5.08 5.08 5.08
12-1.6 DIA. HOLE .200.200.200.200.200
12-.063 DIA. HOLE
mm inch
Inserting and removing method
Inserting method: Insert the relay as
shown in Fig. 1 unit the rib of the relay
snaps into the clip of the socket.
Removing method:
(1) Remove the relay straight from the
socket holding the shaded portion of the
relay as shown in Fig. 2.
Rib
Fig. 1
Fig. 2
(2) When sockets are mounted in close
proximity, use a slotted screw driver as
shown in Fig. 3.
Fig. 3
NOTES
1. Special use of 2 coil latching types: 2
ways can be considered if 2 coil latching
types are used as 1 coil latching types.
(A) Reverse polarity is applied to the set
coil of 2 coil latching type.
(B) By shorting terminals 12 and 7, apply
plus to 1, minus to 6 at set and plus to 6,
minus to 1 at reset. Applied coil voltage
should be the same as the nominal. Oper-
ating power will be reduced to one-half.
Reset position of 2a2b type
123456
-
+
12 11 10 9 8
7
CAUTIONS FOR USE
Based on regulations regarding insulation distance, there is a re-
striction on same-channel load connections between terminals
No. 2, 3 and 4, 5, as well as between No. 8, 9 and 10, 11. See the
figure below for an example.
23
11 10
2. Soldering operations should be accom-
plished as quick as possible; within 10
seconds at 250°C 482°F solder tempera-
ture or 3 seconds at 350°C 662°F. The
header portion being sealed with epoxy
resin, undue subjection to heat may
cause loss of seal. Solder should not be
permitted to remain on the header.
45
98
23
45
11 10
98
• Between 2, 3 and 4, 5: different channels, therefore not possible
• Between 10, 11 and 8, 9: different channels, therefore not possible
No good
• Between 2, 3 and 4, 5: same channels, therefore possible
• Between 10, 11 and 8, 9: same channels, therefore possible
Good
For Cautions for Use, see Relay Technical Information (Page 48 to 76).
92/12/2 000
All Rights Reserved, © Copyright Matsushita Electric Works, Ltd.
Go To Online Catalog
Share Link: 