CE-0929 Просмотр технического описания (PDF) - TDK Corporation
Номер в каталоге
Компоненты Описание
производитель
CE-0929 Datasheet PDF : 6 Pages
| |||
CE-09xx
3
CE-09xx Specifications
ITEMS/UNIT
MODEL CE-0970
Discontinued
CE-0994
Discontinued
CE-0972
Discontinued
CE-0993
Discontinued
CE-0995
Discontinued
Input
Voltage Range Nominal:5VDC
Efficiency (typ)
(*1)
V
％
82
DC4.5-5.5
85
72
75
Nominal Voltage
(*2) V
3.3
12
15
-5
-12
-15
-24
Maximum Current
mA 360
100
80
160
66
53
33
Maximum Power
(*3) W
1.2
0.8
Maximum Line Regulation
Within input voltage range (typ)
0.05%
0.5%
0.02%
0.05%
Output Maximum Load Regulation (0-100%)(typ)
0.1%
1%
0.1%
Temperature Coefficient (-10 to 50°C)(typ) (*4) ％
0.3
3
0.3
Max Power Total Regulation (max) ％
5
Maximum Ripple & Noise (typ) (*5) mVp-p 120
140
170
100
Maximum Ripple & Noise (max)(*5) mVp-p 250
350
250
300
Acceptable Output Capacitorco (*6) μ F 68
22
6.8
Over Current Protection
Available
Not available
Function Over Voltage Protection
Not available
Remote ON/OFF Control
Not available
Operating Temperature
℃
-10 to +70
Storage Temperature
℃
-40 to +85
Environment
Operating Humidity
Storage Humidity
％ RH 10-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.)
％ RH 10-95 (the conditions of maximum 38°C in wet bulb temperature and non-condensation should be ensured.)
Vibration
10-500Hz, 15 minutes sweep and 98m/s² (10G) acceleration, 3 directions, 2h for each, in non-operation
Shock
980m/s² (100G), 6ms, 3 directions, 3 times for each, in non-operation
Mechanical
Weight
Size (W
x
H
x
D)
g
mm
1.2
17.5 x 4.3 x 11.8
(*1) In nominal input voltage, maximum output current, and Ta=25°C.
(*2) 15V in CE 0994 is the value when Vset and +Vset are short-circuited. -15V in CE 0993 is the value when Vset and +Vset are short-circuited.
(*3) The maximum output power value is between -10°C and +50°C. For use outside this temperature rage, derating is needed.
(*4) Temperature coefficient in -10°C - +50°C.
(*5) Frequency range in measurement (50MHz). Ripple & noise value is that in the condition where a specified external output capacitor Co is attached to the output termi-
nal.
(*6) Use an external output capacitor with 3Ωmax. impedance and 0.06 max. loss angle. Recommended capacitor: TE series (MATSUSHITA)
With nominal input/output voltage, maximum output current, and Ta=25°C, if not specified separately.
Metal case
Outline Drawing
8-ø0.8
Cut-through hole
1.3
Recommended measurements for board mounting
1
8
CE-09xx
2
TDK-Lambda
7
3
MADE IN JAPAN
6
4
Lot No.
5
17.5
P=2.0
(0.7)
・Case is connected to GND.
if not specified separately.
Unit: mm
Derating Curve
14.9
(18.9)
・All specifications are subject to change without notice.
100
80
60
50
40
20
0–10 0
30
50
70 80
Ambient temperature (°C)
Output power derating by ambient temperature
Share Link: 