MAL212380688 Просмотр технического описания (PDF) - Vishay Semiconductors
Номер в каталоге
Компоненты Описание
производитель
MAL212380688 Datasheet PDF : 13 Pages
| |||
End of Life. Last Available Purchase Date is 30-December-2015
www.vishay.com
123 SAL-A
Vishay BCcomponents
EQUIVALENT SERIES RESISTANCE (ESR)
102
ESR
(Ω)
1
10
2
3
1
4
Curve 1: 68 µF, 35 and 40 V
Curve 2: 150 µF, 25 V
Curve 3: 330 µF, 10 V
Curve 4: 470 µF, 10 V
102
ESR
(Ω) 1
10
2
3
4
15
Curve 1: 100 µF, 35 and 40 V
Curve 2: 150 µF, 35 V
Curve 3: 220 µF, 25 V
Curve 4: 470 µF, 16 V
Curve 5: 680 µF, 10 V; 1000 µF, 6.3 V
10-1
10-1
10-2 Case Ø D x L = 9.4 x 23.3 mm
1
10
10 2
10 3
ESR at 100 Hz
10 4
10
5
f
(Hz)
10 6
Fig. 27 - Typical ESR as a function of ambient temperature
Case Ø D x L = 9.4 x 23.3 mm
10-2
1
10
10 2
10 3
ESR at 100 Hz
10 4
10
5
f
(Hz)
10 6
Fig. 28 - Typical ESR as a function of ambient temperature
Table 3
TEST PROCEDURES AND REQUIREMENTS
TEST
NAME OF TEST
REFERENCE
PROCEDURE
(quick reference)
Endurance
IEC 60384-4/
EN130300
subclause 4.13
Tamb = 125 °C;
UR = 6.3 V to 25 V with UR applied;
UR = 35 V and 40 V with UC applied;
10 000 h
Useful life
CECC 30302
subclause 1.8.1
Tamb = 125 °C; IR applied and
UR = 6.3 V to 25 V with UR applied;
UR = 35 V and 40 V with UC applied;
20 000 h
Shelf life
(storage at high
temperature)
Charge and
discharge
IEC 60384-4/
EN130300
subclause 4.17
IEC 60384-4-2
subclause 9.21
Tamb = 125 °C; no voltage applied;
500 h
106 cycles without series resistance:
0.5 s to UR;
0.5 s to ground
Shock
IEC 60068-2-27
test Ea
Half-sine or saw tooth pulse shape; 50 g; 11 ms;
3 successive shocks in each direction of
3 mutually perpendicular axes;
no voltage applied
Severe rapid change
of temperature
Solvent resistance
IEC 60068-2-45,
test XA
IEC 60653
Passive flammability IEC 60695-2-2
100 cycles of 1 h duration, each with
30 min at - 40 °C and + 125 °C
Immersion:
5 min ± 0.5 min with or without ultrasonic
at 55 °C ± 5 °C
Solvents: demineralized water and/or calgonite
solution (20 g/l)
Capacitor mounted to a vertical printed-circuit
board, one flame on capacitor body;
Tamb = 20 °C to 25 °C;
test duration = 20 s
REQUIREMENTS
C/C: ± 10 %
tan 1.2 x spec. limit
Z 1.2 x spec. limit
IL5 spec. limit
C/C: ± 15 %
tan 1.5 x spec. limit
Z 1.5 x spec. limit
IL5 spec. limit
no short or open circuit,
no visible damage
total failure percentage: < 1 %
C/C: ± 10 %
tan 1.2 x spec. limit
IL5 1 x spec. limit
C/C: ± 5 %
no short or open circuit,
no visible damage
no intermittent contacts
no breakdown
no open circuiting
no mechanical damage
C/C: ± 5 %
tan 1.2 x spec. limit
Z 1.2 x spec. limit
IL5 1.5 x spec. limit
C/C: ± 25 %
tan 1.5 x spec. limit
Z 2.0 x spec. limit
IL5 1 x spec.limit
Visual appearance not affected
After removing the test flame from the
capacitor, the capacitor must not
continue to burn for more than 15 s;
no burning particles must drop from
the sample
Revision: 14-Aug-15
10
Document Number: 28355
For technical questions, contact: aluminumcaps2@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Share Link: 