CA3028A Просмотр технического описания (PDF) - Intersil
Номер в каталоге
Компоненты Описание
производитель
CA3028A Datasheet PDF : 10 Pages
| |||
CA3028A
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (oC/W) θJC (oC/W)
Metal Can Package . . . . . . . . . . . . . . . 225
140
PDIP Package . . . . . . . . . . . . . . . . . . . 155
N/A
SOIC Package . . . . . . . . . . . . . . . . . . . 185
N/A
Maximum Junction Temperature (Metal Can Package). . . . . . . .175oC
Maximum Junction Temperature (Plastic Package) . . . . . . . .150oC
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC
(SOIC - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
Absolute Maximum Voltage Ratings TA = 25oC
The following chart gives the range of voltages which can be applied to the terminals listed horizontally with
respect to the terminals listed vertically. For example, the voltage range of the horizontal Terminal 4 with
respect to Terminal 2 is -1V to +5V.
Absolute Maximum
Current Ratings
TERM
NO.
1
2
3
4
5
6
7
8
TERM
IIN
IOUT
NO.
mA
mA
1
0 to -15 0 to -15 0 to -15 +5 to -5 Note 3 Note 3 +20 to 0
1
0.6
0.1
2
+5 to -11 +5 to -1 +15 to 0 Note 3 +15 to 0 Note 3
2
4
0.1
3 (Note 2)
+10 to 0 +15 to 0 +24 to 0 +15 to 0 +24 to 0
3
0.1
23
4
+15 to 0 Note 3 Note 3 Note 3
4
20
0.1
5
+20 to 0 Note 3 Note 3
5
0.6
0.1
6
Note 3 Note 3
6
20
0.1
7
Note 3
7
4
0.1
8
8
20
0.1
NOTES:
2. Terminal No. 3 is connected to the substrate and case.
3. Voltages are not normally applied between these terminals. Voltages appearing between these terminals
will be safe, if the specified voltage limits between all other terminals are not exceeded.
Electrical Specifications TA = 25oC
PARAMETER
SYMBOL
TEST CONDITIONS
MIN TYP MAX UNIT
DC CHARACTERISTICS
Input Bias Current (Figures 1, 10)
Quiescent Operating Current (Figures 1,11, 12)
AGC Bias Current (Into Constant Current Source
Terminal 7) (Figures 2, 13)
Input Current (Terminal 7)
Power Dissipation (Figures 1, 14)
II
I6, I8
I7
I7
PT
VCC = 6V, VEE = -6V
VCC = 12V, VEE = -12V
VCC = 6V, VEE = -6V
VCC = 12V, VEE = -12V
VCC = 12V, VAGC = 9V
VCC = 12V, VAGC = 12V
VCC = 6V, VEE = -6V
VCC = 12V, VEE = -12V
VCC = 6V, VEE = -6V
VCC = 12V, VEE = -12V
- 16.6 70 µA
-
36 106 µA
0.8 1.25 2.0 mA
2.0 3.3 5.0 mA
- 1.28 - mA
- 1.65 - mA
0.5 0.85 1.0 mA
1.0 1.65 2.1 mA
24 36 54 mW
120 175 260 mW
2
Share Link: 