LF3310QC12 Просмотр технического описания (PDF) - LOGIC Devices
Номер в каталоге
Компоненты Описание
производитель
LF3310QC12 Datasheet PDF : 21 Pages
| |||
DEVICES INCORPORATED
LF3310
Horizontal / Vertical Digital Image Filter
changed every clock cycle. This is
useful when filtering interleaved
data. When loading limit values into
the device, the upper limit must be
greater than the lower limit. Limit
register loading is discussed in the LF
InterfaceTM section.
Vertical Filter
The vertical filter is designed to filter
a digital image in the vertical dimen-
sion. It is a FIR filter which can be
configured to have as many as 8-taps.
Line Buffers
There are seven on-chip line buffers.
The maximum delay length of each
line buffer is 3076 cycles and the
minimum is 4 cycles. Configuration
Register 2 (CR2) determines the delay
length of the line buffers. The line
buffer length is equal to the value of
CR2 plus 4. A value of 0 for CR2 sets
the line buffer length to 4. A value of
3072 for CR2 sets the line buffer
length to 3076. Any values for CR2
greater than 3072 are not valid.
section for a full discussion). When in
Orthogonal Mode, VSHEN also
enables or disables the loading of data
into the input register (DIN11-0) and
the forward and reverse I/D Registers.
It is important to note that in Or-
thogonal Mode, either HSHEN or
VSHEN can disable the loading of
data into the input register (DIN11-0),
I/D Registers, and line buffers. Both
must be active to enable data loading
in Orthogonal Mode.
Interleaved Data
The vertical filter is capable of
handling interleaved data. The
number of data sets it can handle is
determined by the number of data
values contained in a video line. If
the interleaved video line has 3076
data values or less, the vertical filter
can handle it no matter how many
data sets are interleaved together.
TABLE 4. CONFIGURATION REGISTER 2 – ADDRESS 202H
BITS FUNCTION
DESCRIPTION
11-0 Line Buffer Length
See Line Buffer Description Section
TABLE 5. CONFIGURATION REGISTER 3 – ADDRESS 203H
BITS FUNCTION
DESCRIPTION
0
Line Buffer Mode
0 : Delay Mode
1 : Recirculate Mode
1
Line Buffer Load
0 : Normal Load
1 : Parallel Load
11-2 Reserved
Must be set to “0”
The line buffers have two modes of
operation: delay mode and recirculate
mode. Bit 0 of Configuration Register
3 determines which mode the line
buffers are in. In delay mode, the
data input to the line buffer is delayed
by an amount determined by CR2. In
recirculate mode, the output of the
line buffer is routed back to the input
of the line buffer allowing the line
buffer contents to be read multiple
times.
Bit 1 of Configuration Register 3
allows the line buffers to be loaded in
parallel. When Bit 1 is “1”, the input
register (DIN11-0) loads all seven line
buffers in parallel. This allows all the
line buffers to be preloaded with data
in the amount of time it normally
takes to load a single line buffer.
VSHEN enables or disables the
loading of data into the line buffers
when the device is in Dimensionally
Separate Mode (see the VSHEN
TABLE 6. CONFIGURATION REGISTER 4 – ADDRESS 204H
BITS FUNCTION
DESCRIPTION
0
HV Filter Mode
0 : Orthogonal Mode
1 : Dimensionally Separate
1
HV Direction
0 : Horizontal to Vertical
1 : Vertical to Horizontal
3-2
Orthogonal Kernel Size
00 : 3-3 Kernel
01 : 5-5 Kernel
10 : 7-7 Kernel
11 : Not Used
4
Limit Register Load Control 0 : Limit Registers Always Enabled
1 : Limit Registers Under Shift Enable Control
11-5 Reserved
Must be set to “0”
TABLE 7. CONFIGURATION REGISTER 5 – ADDRESS 205H
BITS FUNCTION
DESCRIPTION
0
Vertical Limit Enable
0 : Vertical Limiting Disabled
1 : Vertical Limiting Enabled
1
Horizontal Limit Enable
0 : Horizontal Limiting Disabled
1 : Horizontal Limiting Enabled
11-2 Reserved
Must be set to “0”
Video Imaging Products
10
11/08/2001-LDS.3310-H
Share Link: 