IDT70V06L(2000) Просмотр технического описания (PDF) - Integrated Device Technology
Номер в каталоге
Компоненты Описание
производитель
IDT70V06L Datasheet PDF : 22 Pages
| |||
IDT70V06S/L
High-Speed 16K x 8 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
AC Electrical Characteristics Over the
Operating Temperature and Supply Voltage(5)
70V06X15
Com'l Only
70V06X20
Com'l
& Ind
70V06X25
Com'l
& Ind
Symbol
Parameter
Min. Max. Min. Max. Min. Max. Unit
WRITE CYCLE
tWC
Write Cycle Time
tEW
Chip Enable to End-of-Write(3)
15
____
20
____
25
____
ns
12
____
15
____
20
____
ns
tAW
Address Valid to End-of-Write
tAS
Address Set-up Time(3)
12
____
15
____
20
____
ns
0
____
0
____
0
____
ns
tWP
Write Pulse Width
12
____
15
____
20
____
ns
tWR
Write Recovery Time
0
____
0
____
0
____
ns
tDW
Data Valid to End-of-Write
tHZ
Output High-Z Time(1,2)
tDH
Data Hold Time(4)
tWZ
Write Enable to Output in High-Z(1,2)
tOW
Output Active from End-of-Write(1,2,4)
10
____
15
____
15
____
ns
____
10
____
12
____
15
ns
0
____
0
____
0
____
ns
____
10
____
12
____
15
ns
0
____
0
____
0
____
ns
tSWRD
SEM Flag Write to Read Time
5
____
5
____
5
____
ns
tSPS
SEM Flag Contention Window
5
____
5
____
5
____
ns
2942 tbl 12a
70V06X35
Com'l
& Ind
70V06X55
Com'l
& Ind
Symbol
Parameter
Min. Max. Min. Max. Unit
WRITE CYCLE
tWC
Write Cycle Time
tEW
Chip Enable to End-of-Write(3)
35
____
55
____
ns
30
____
45
____
ns
tAW
Address Valid to End-of-Write
tAS
Address Set-up Time(3)
30
____
45
____
ns
0
____
0
____
ns
tWP
Write Pulse Width
25
____
40
____
ns
tWR
Write Recovery Time
0
____
0
____
ns
tDW
Data Valid to End-of-Write
tHZ
Output High-Z Time(1,2)
tDH
Data Hold Time(4)
tWZ
Write Enable to Output in High-Z(1,2)
tOW
Output Active from End-of-Write(1,2,4)
15
____
30
____
ns
____
15
____
25
ns
0
____
0
____
ns
____
15
____
25
ns
0
____
0
____
ns
tSWRD
SEM Flag Write to Read Time
5
____
5
____
ns
tSPS
SEM Flag Contention Window
5
____
5
____
ns
NOTES:
2942 tbl 12b
1. Transition is measured 0mV from Low or High-impedance voltage with the Output Test Load (Figure 2).
2. This parameter is guaranteed but not tested.
3. To access SRAM, CE = VIL, SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. Either condition must be valid for the entire tEW time.
4. The specification for tDH must be met by the device supplying write data to the RAM under all operating conditions. Although tDH and tOW values will vary over voltage and
temperature, the actual tDH will always be smaller than the actual tOW.
5. 'X' in part number indicates power rating (S or L).
10
Share Link: 