HDC136 Просмотр технического описания (PDF) - Optek Technology

Номер в каталоге

Компоненты Описание

производитель

HDC136

High Speed Optocouplers

Optek Technology 

Product Bulletin HDC135

September 1996

High Speed Optocouplers

Types HDC135, HDC136, HDC135B, HDC136B

Features

• High speed

• TTL compatible

• High common mode transient

immunity

• Wide bandwidth

• Open collector output

Description

Optek’s HDC135 and HDC136 are high

speed optocouplers, consisting of IR

emitters and integrated photodetectors

in hermetic side brazed dual-in-line 8 pin

packages. Electrical characteristics are

similar to the 6N135 and 6N136

optocouplers but with full military

temperature range operation.

The HDC135B and HDC136B are high

reliability optocouplers with 100%

processing and Group Testing patterned

after MIL-STD-883 Method 5004 and

5005 for class B.

Typical screening and lot acceptance

tests are provided on page 13-4.

Absolute Maximum Ratings (No derating required up to 70o C)

Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55o C to +150o C

Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55o C to +125o C

Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 10 seconds) . 260o C

Average Input Current - IF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 mA(1)

Peak Output Current - IF (50% duty cycle, 1 ms pulse width) . . . . . . . . . . . . 50 mA(2)

Peak Transient Input Current - IF (≤1 µs pulse width, 300 pps) . . . . . . . . . . . . . 1.0 A

Reverse Input Voltage - VR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 V

Input Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 mW(3)

Average Output Current - IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.0 mA

Peak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.0 mA

Emitter-Base Reverse Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 V

Supply and Output Voltage - VCC, VO . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 15 V

Base Current - IB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 mA

Output Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mW(4)

Caution: This component is susceptible to damage from electrostatic discharge. Normal static

prevention procedures should be used in handling.

Notes:

(1) Derate linearly above 70o C free-air temperature at a rate of 0.45 mA/o C.

(2) Derate linearly above 70o C free-air temperature at a rate of 0.9 mA/o C.

(3) Derate linearly above 70o C free-air temperature at a rate of 0.8 mW/o C.

(4) Derate linearly above 70o C free-air temperature at a rate of 1.8 mW/o C.

(5) CMH is the maximum allowable dV/dt on the leading edge of a common mode pulse to

assure that the output will not switch from high to low.

(6) CML is the maximum negative dV/dt allowable on the trailing edge of a common mode pulse

to assure that the output will not switch from low to high.

(7) Test conditions represents 1 TTL unit load with 5.6 kΩ pull-up resistor.

(8) Test conditions represents 1 LSTTL unit load with a 6.1 kΩ pull-up resistor.

(9) Device considered a two-terminal device: pins 2 and 3 shorted together and pins 5, 6, 7 and

8 shorted together.

Minimum orders will apply to processed

devices.

Optek Technology, Inc.

1215 W. Crosby Road

Carrollton, Texas 75006

13-22

(214) 323-2200

Fax (214) 323-2396

Share Link: