SCIW1000 Просмотр технического описания (PDF) - Unspecified

Номер в каталоге

Компоненты Описание

производитель

SCIW1000

Inside Wiring and Networks Service Meter

Unspecified 

6

Specifications and Features

SMARTCLASS IW-1000

Available Configurations

Physcial layer testing (coax and twisted pair), Ethernet,

Butt-Set

Optional wireless 802.11b/g WiFi

Physical Test Interfaces

Coax F-connector for coax mapping, NIT

RJ11 for POTS testing

RJ11 for phone wiring and dry pair testing

RJ45 for Cat5/6 wiring and Ethernet testing

Connector LEDs for easy connector identification

Cable ID and Toning Specifications

Cable ID Features

Supports coax, Cat3/Cat5/Cat6 cable

Test via F-connector, RJ11, or RJ45

Supports 8 ID devices on each interface

Timing Features

Sends four types of tones on all leads

Constant High pitch (976 Hz)

Constant Low pitch (651 Hz)

High pitch then a low pitch

Low pitch with a short high pitch

Coax Mapping Specifications

Settings

Support any cable coax type with configurable velocity of

propagation (VOP) and cable compensation

Features

Measures cable length in feet (up to 500 ft at ±5 ft)

Measures return loss in dBrl (up to 20 dBrl at ±2 dB)

Cable Events Identified

Open, splitter, low-quality splitter, barrel/splice

Noise Immunity Test Specifications

Features

Measures cable shield isolation vs. settable threshold

(def 30 dB)

Specifications

Test frequency of 88 to 108 MHz

Active Identification Specifications

Features

Identifies coax cables through most coax network elements

Identifies multiple IDs attached to the branch of coax being

tested

Specifications

IDs with up to 15 dB of signal loss between unit and ID

Wiring Tool Specifications

General Features

Supports Cat3, Cat5/6, coax cable

Detects power present on cables being tested

Measures cable length based on capacitance setting

Detects opens, shorts, and crossed pairs and display wires

mapping

Dry Pair Specifications

General Features

Identifies resistive opens and shorts on dry twisted pair

Reports AC voltage presence or DC voltage presence on dry

twisted pair (up to 120 VDC, 120 Vrms AC)

Ethernet Testing Specifications

Features

Supports 10/100 Mbps testing over RJ45 interface

Port Discovery

Identifies Ethernet setting on port

Displays link rate

Reports pair skew

Reports frequency offset in ppm

Ping Test

Supports manual or DHCP IP configuration

Reports packets sent and received

Reports average test packet delay

Butt-Set Specifications

North American POTS Butt-Set Only

Features

Supports loop start dial tone POTS testing on twisted pair

Supports receiving a call

Supports line monitor mode with DTMF decode

Supports caller ID, call waiting, with caller ID errors

Microphone and speakerphone support

Measures voltage from 0 to 105 V, ±4%

Measures loop current from 14 to 108 mA ±4%

General Specifications

Power Supply

Field replaceable, rechargeable lithium ion battery

Operating time approximately 4.5 hrs continuous (typical)

Charging time, internal 4-5 hrs from empty to full charge

DC input 12 V, 1.25 A

100/240 V, 50 Hz/60 Hz auto-sensing AC adapter for line

operation and charging

Possible Ambient Temperature

Nominal range of use

–5 to +50°C (23 to +120°F)

Storage and transport

–30 to +60°C (–22 to ±140°F)

Humidity

Operating humidity

10 to 80% RHNC

Physical Specifications

4 in 320x240 high visibility color display

USB 2.0 interface for upgrades and data transfer

Full telephone keypad for fast access and dialing

Optional WiFi Specifications

Features

Detects all available WiFi (802.11 b/g) networks

Reports power level, operating mode, security setting, 802.11

version, channel, SSID, and MAC

Share Link: