MSK0033(2011) Просмотр технического описания (PDF) - M.S. Kennedy
Номер в каталоге
Компоненты Описание
производитель
MSK0033 Datasheet PDF : 6 Pages
| |||
ABSOLUTE MAXIMUM RATINGS 10
±VCC
Supply Voltage ±20V ○
○
○
○
○
○
○
○
○
○
○
○
○
TST
Storage Temperature Range -65°C to +150°C
IOUT
Output Current ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ±120mA TLD Lead Temperature Range○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 300°C
VIN
Differential Input Voltage ○ ○ ○ ○ ○ ○ ○ ○ ±20V
(10 Seconds)
TC
Case Operating Temperature
TJ
Junction Temperature ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 175°C
(MSK 0033B) ○ ○ ○ ○ ○ ○ ○ -55°C to +125°C RTH Thermal Resistance ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 65°C/W
(MSK 0033) ○ ○ ○ ○ ○ ○ ○ ○ -40°C to +85°C
Junction to Case
Output Devices Only
ELECTRICAL SPECIFICATIONS
Parameter
Test Conditions
Group A
MSK 0033B
MSK 0033
Subgroup Min. Typ. Max. Min. Typ. Max.
Units
STATIC
Supply Voltage Range 3 8
-
±10 ±15 ±18 ±10 ±15 ±18
V
Quiescent Current
VIN=0V
1
-
±19 ±22 -
±19 ±25 mA
INPUT
Offset Voltage
Short Pin 6 to Pin 7 VIN=0V
1
- ±2.0 ±10 -
±5 ±15 mV
Offset Voltage Drift
Offset Adjust
Short Pin 6 to Pin 7 VIN=0V
Pin 6=open RPOT=200Ω From Pin 7 to Pin 9
2,3
1,2,3
-
±25 ±250
Adjust to Zero
-
-
-
Adjust to Zero
μV/°C
mV
Input Bias Current 9
VCM=0V
1
-
±50 ±100 -
±50 ±500 pA
Either Input
2,3
-
±2 ±10 -
±2
-
nA
Input Impedance 3
F=DC
-
-
1012
-
-
10 12
-
Ω
Power Supply Rejection Ratio 2
±10V≤VS≤±20V
-
65
75
-
60
75
-
dB
Input Noise Density 3
F=10Hz to 1KHz
-
-
1.5
-
-
1.5
- μVRMS
Input Noise Voltage 3
F=1KHz
-
-
40
-
-
40
- nV/√Hz
OUTPUT
Output Voltage Swing
VIN=±14V RL=1KΩ
4
±12 ±12.5 - ±12 ±12.5 -
V
Output Current
VIN=±10.5V RL=100Ω
4
±90 ±110 - ±90 ±110 -
mA
Settling Time to 1% 2 3
2V step
-
-
25
-
-
25
-
nS
Bandwidth (-3dB) 3
VIN=1VRMS RL=1KΩ
-
-
140
-
-
140
-
MHz
TRANSFER CHARACTERISTICS
Slew Rate-Rising Edge
VOUT=±10V
4
1000 1500 - 1000 1500 -
V/μS
Slew Rate-Falling Edge
VOUT=±10V
4
500 700
- 500 700
-
V/μS
Voltage Gain
RS=100Ω VIN=1VRMS F=1KHz
4
0.97 0.99
- 0.95 0.98
-
V/V
NOTES:
1 Unless otherwise specified ±VCC = ±15 VDC.
2 Measured within a high speed amplifier feedback loop.
3 Devices shall be capable of meeting the parameter, but need not be tested. Typical parameters are for reference only.
4 Industrial grade devices shall be tested to subgroups 1 and 4 unless otherwise specified.
5 Military grade devices ('B' suffix) shall be 100% tested to subgroups 1,2,3 and 4.
6 Subgroup 5 and 6 testing available upon request.
7 Subgroup 1,4
TA=TC=+25°C
Subgroup 2,5
TA=TC=+125°C
Subgroup 3,6
TA=TC=-55°C
8 Electrical specifications are derated for power supply voltages other than ±15VDC.
9 Measurement made 0.5 seconds after application of power. Actual DC continuous test limit is 2.5 nA at 25°C.
10 Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle.
2
8548-8 Rev. E 12/11
Share Link: 