OP150 Просмотр технического описания (PDF) - Analog Devices
Номер в каталоге
Компоненты Описание
производитель
OP150 Datasheet PDF : 5 Pages
| |||
OP150/OP250/OP450
ELECTRICAL CHARACTERISTICS (@ VS = +5.0 V, VCM = 0.05 V, VO = 1.4 V, TA = +25؇C, unless otherwise noted)
Parameter
Symbol
Conditions
Min
Typ
Max Units
INPUT CHARACTERISTICS
Offset Voltage OP150
VOS
–40°C ≤ TA ≤ +125°C
5
mV
mV
Offset Voltage OP250/OP450
VOS
–40°C ≤ TA ≤ +125°C
5
mV
mV
Input Bias Current
IB
–40°C ≤ TA ≤ +125°C
30
50 pA
60 pA
Input Offset Current
IOS
0.1
8
pA
OBSOLETE Input Voltage Range
–40°C ≤ TA ≤ +125°C
0
Common-Mode Rejection Ratio CMRR
VCM = 0 V to 5 V
60
–40°C ≤ TA ≤ +125°C
Large Signal Voltage Gain
AVO
RL = 10 kΩ, VO = 0.3 V to 4.7 V
–40°C ≤ TA ≤ +125°C
Large Signal Voltage Gain
AVO
RL = 2 kΩ, VO = 0.3 V to 2.7 V
Large Signal Voltage Gain
AVO
RL = 1 kΩ, VO = 0.3 V to 2.7 V
Offset Voltage Drift
∆VOS/∆T
–40°C ≤ TA ≤ +125°C
Bias Current Drift
∆IB/∆T
Offset Current Drift
∆IOS/∆T
OUTPUT CHARACTERISTICS
Output Voltage High
VOH
Output Voltage Low
VOL
IL = 100 µA
–40°C to +125°C
IL = 10 mA
–40°C to +125°C
IL = 100 µA
16 pA
5
V
dB
dB
40
V/mV
V/mV
16
V/mV
10
V/mV
1.5
µV/°C
100
pA/°C
20
pA/°C
4.99
V
V
4.95
V
V
2
mV
–40°C to +125°C
mV
IL = 10 mA
–40°C to +125°C
30
mV
mV
Output Current
IOUT
–40°C to +125°C
± 250
mA
mA
Open Loop Impedance
ZOUT
f = 1 MHz, AV = 1
Ω
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current/Amplifier
DYNAMIC PERFORMANCE
Slew Rate
Full Power Bandwidth
Settling Time
Gain Bandwidth Product
Phase Margin
Channel Separation
NOISE PERFORMANCE
Voltage Noise
Voltage Noise Density
Voltage Noise Density
Current Noise Density
PSRR
ISY
SR
BWp
tS
GBP
Øo
CS
en p-p
en
en
in
VS = 2.7 V to 6 V
–40°C ≤ TA ≤ +125°C
VO = 0 V
–40°C ≤ TA ≤ +125°C
RL =10 kΩ
1% Distortion
To 0.01%
f = 1 kHz, RL =10 kΩ
0.1 Hz to 10 Hz
f = 1 kHz
f = 10 kHz
75
dB
70
dB
µA
550
650 µA
6.5
V/µs
kHz
µs
4
MHz
75
Degrees
dB
µV p-p
55
nV/√Hz
35
nV/√Hz
pA/√Hz
Specifications subject to change without notice.
This information applies to a product under development. Its characteristics and specifications are subject to change without notice.
Analog Devices assumes no obligation regarding future manufacture unless otherwise agreed to in writing.
REV. 0
–3–
PRELIMINARY TECHNICAL DATA
Share Link: 