PCX1C820MCL1GS Просмотр технического описания (PDF) - Nichicon
Номер в каталоге
Компоненты Описание
производитель
PCX1C820MCL1GS Datasheet PDF : 2 Pages
| |||
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
PCX Chip Type, High Voltage / Long Life
High reliability, High voltage (to 50V).
Low ESR, High ripple current.
Long life of 1500 to 3000 hours at 125°C.
SMD type : Lead free reflow soldering condition at
260°C peak complete correspondence.
Compliant to the RoHS directive (2011/65/EU).
AEC-Q200 compliant. Please contact us for details.
Specifications
PCR
Higher
Capacitance
PCX
Higher
Temperature
PCV
Item
Performance Characteristics
Category Temperature Range – 55 to +125°C
Rated Voltage Range
16 to 50V
Rated Capacitance Range 5.6 to 390µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2)
Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+125°C / Z+20°C 1.25
Z– 55°C / Z+20°C 1.25
(100kHz)
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 3000 hours (φD = 6.3:1500hours) at 125°C.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of initial capacitance value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of initial capacitance value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In case peak temperature is 250°C or less, reflow soldering shall be
two times maximum.
In case peak temperature is 260°C or less, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Type numbering system (Example : 35V 39µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Dimensions
Standard
Capacitance
Lot No.
Plastic platform
0.3 MAX.
C±0.2
Positive
PCX 1 V 3 9 0 MC L 1 GS
Taping code
Size code
Configuration
Capacitance tolerance (±20%) Configuration code
Rated capacitance (39µF)
Standard
L
Vibration Resistance S
Rated voltage (35V)
Series name
Type
Series
Voltage (V:35V)
L
+0.1
- 0.4
H
Vibration Resistance
Capacitance
Lot No.
Plastic platform
0.3 MAX.
C±0.2
Negative
Positive
Standard
(mm) Vibration Resistance (mm)
Size φ6.3 ×6L φ6.3 ×8L φ8 ×7L φ8 ×10L φ8 ×12L φ10 ×8L φ10 ×10L φ10×12.7L Size φ6.3 ×8L φ8×10.5L φ10×10.5L φ10×13.2L
φD 6.3 6.3 8.0 8.0 8.0 10.0 10.0 10.0 φD 6.3 8.0 10.0 10.0
L 5.9 7.9 6.9 9.9 11.9 7.9 9.9 12.6 L 7.5 10.0 10.0 12.7
A 7.3 7.3 9.0 9.0 9.0 11.0 11.0 11.0 A 7.3 9.0 11.0 11.0
B 6.6 6.6 8.3 8.3 8.3 10.3 10.3 10.3 B 6.6 8.3 10.3 10.3
C 6.6 6.6 8.3 8.3 8.3 10.3 10.3 10.3 C 6.6 8.3 10.3 10.3
E 2.1 2.1 3.2 3.2 3.2 4.6 4.6 4.6 E 2.5 3.1 4.6 4.6
H 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 H 0.5 to 0.8 1.1 to 1.5 1.1 to 1.5 1.1 to 1.5
Series
Voltage (V:35V)
L±0.5
Dimension table in next page.
H
Negative
Aid electrode
52
Voltage
V 16 20 25 35 50
Code C D E V H
Frequency coefficient of rated ripple current
Frequency 120Hz 1kHz 10kHz 100kHz or more
Coefficient 0.05 0.30 0.70 1.00
φ10× 12.7L : The vibration structure-resistant product
is also available upon request, please ask for details.
CAT.8100H
Share Link: 