AD1870JR Просмотр технического описания (PDF) - Analog Devices

Номер в каталоге

Компоненты Описание

производитель

AD1870JR

Single-Supply 16-Bit ∑-∆ Stereo ADC

Analog Devices 

AD1870

The AD1870 achieves its specified performance without the

need for user trims or adjustments. This is accomplished through

the use of on-chip automatic offset calibration that takes place

immediately following reset. This procedure nulls out any off-

sets in the single-to-differential converter, the analog modulator,

and the decimation filter. Autocalibration completes in approxi-

mately 8192 × (1/(FLRCK) seconds, and need only be performed

once at power-up in most applications. (In slave mode, the 8192

cycles required for autocalibration do not start until after the

first rising edge of LRCK following the first falling edge of

LRCK.) The autocalibration scheme assumes that the inputs

are ac-coupled. DC-coupled inputs will work with the AD1870,

but the autocalibration algorithm will yield an incorrect offset

compensation.

The AD1870 also features a power-down mode. It is enabled by

the active LO RESET Pin 23 (i.e., the AD1870 is in power-down

mode while RESET is held LO). The power savings are speci-

fied in the “Specifications’’ section above. The converter is shut

down in the power-down state and will not perform conversions.

The AD1870 will be reset upon leaving the power-down state, and

autocalibration will commence after the RESET pin goes HI.

Power consumption can be further reduced by slowing down the

master clock input (at the expense of input passband width).

Note that a minimum clock frequency, fCLKIN, is specified for

the AD1870.

Tag Overrange Output

The AD1870 includes a TAG serial output (Pin 27) which is

provided to indicate status on the level of the input voltage. The

TAG output is at TTL-compatible logic levels. A pair of unsigned

binary bits are output, synchronous with LRCK (MSB then

LSB), that indicate whether the current signal being converted

is: more than 1 dB under full scale; within 1 dB under full scale;

within 1 dB over full scale; or more than 1 dB over full scale.

The timing for the TAG output is shown in TPCs 7 through 16.

Note that the TAG bits are not “sticky”; i.e., they are not peak

reading, but rather change with every sample. Decoding of these

two bits is as follows:

TAG Bits

MSB, LSB

0

0

0

1

1

0

1

1

Meaning

More Than 1 dB Under Full Scale

Within 1 dB Under Full Scale

Within 1 dB Over Full Scale

More Than 1 dB Over Full Scale

APPLICATIONS ISSUES

Recommended Input Structure

The AD1870 input structure is single-ended to allow the board

designer to achieve a high level of functional integration. The

very simple recommended input circuit is shown in Figure 2. Note

the 1 µF ac-coupling capacitor, which allows input level shifting

for 5 V only operation, and for autocalibration to properly null

offsets. The 3 dB point of the single-pole antialias RC filter is

240 kHz, which results in essentially no attenuation at 20 kHz.

Attenuation at 3 MHz is approximately 22 dB, which is adequate

to suppress fS noise modulation. If the analog inputs are exter-

nally ac-coupled, the 1 µF ac-coupling capacitors shown in

Figure 2 are not required.

RIGHT

INPUT

LEFT

INPUT

300⍀

1␮F

2.2nF

NPO

300⍀

1␮F

2.2nF

NPO

VINR

AD1870

VINL

Figure 2. Recommended Input Structure for Externally

DC-Coupled Inputs

Analog Input Voltage Swing

The single-ended input range of the analog inputs is specified in

relative terms in the “Specifications” section of this data sheet.

The input level at which clipping occurs linearly tracks the voltage

reference level, i.e., if the reference is high relative to the typical

2.25 V, the allowable input range without clipping is corre-

spondingly wider; if the reference is low relative to the typical

2.25 V, the allowable input range is correspondingly narrower.

Thus the maximum input voltage swing can be computed using

the following ratio:

2.25 V (nominal reference voltage)

X Volts (measured reference voltage)

=

2.983 V p −p (nominal voltage swing ) Y Volts (maximum swing without clipping)

REV. 0

–9–

Share Link: