SY87701VZCTR Просмотр технического описания (PDF) - Micrel

Номер в каталоге

Компоненты Описание

производитель

SY87701VZCTR

5V/3.3V 32-1250Mbps AnyRate® CLOCK AND DATA RECOVERY

Micrel 

Micrel, Inc.

SY87701V

PIN DESCRIPTIONS

INPUTS

OUTPUTS

RDINP, RDINN [Serial Data Input] Differential PECL.

These built-in line receiver inputs are connected to the

differential receive serial data stream. An internal receive

PLL recovers the embedded clock (RCLK) and data

(RDOUT) information. The incoming data rate can be within

one of eight frequency ranges depending on the state of

the FREQSEL pins. See “Frequency Selection” Table.

LFIN [Link Fault Indicator] TTL Output.

This output indicates the status of the input data stream

RDIN. Active HIGH signal is indicating when the internal

clock recovery PLL has locked onto the incoming data

stream. LFIN will go HIGH if CD is HIGH and RDIN is within

the frequency range of the Receive PLL (1000ppm). LFIN

is an asynchronous output.

REFCLK [Reference Clock] TTL Input.

This input is used as the reference for the internal

frequency synthesizer and the “training” frequency for the

receiver PLL to keep it centered in the absence of data

coming in on the RDIN inputs.

CD [Carrier Detect] PECL Input.

This input controls the recovery function of the Receive

PLL and can be driven by the carrier detect output of optical

modules or from external transition detection circuitry. When

this input is HIGH the input data stream (RDIN) is recovered

normally by the Receive PLL. When this input is LOW the

data on the inputs RDIN will be internally forced to a constant

LOW, the data outputs RDOUT will remain LOW, the Link

Fault Indicator output LFIN forced LOW and the clock

recovery PLL forced to lock onto the clock frequency

generated from REFCLK.

FREQSEL1, ..., FREQSEL3 [Frequency Select] TTL

Inputs.

These inputs select the output clock frequency range as

shown in the “Frequency Selection” Table.

DIVSEL1, DIVSEL2 [Divider Select] TTL Inputs.

These inputs select the ratio between the output clock

frequency (RCLK/TCLK) and the REFCLK input frequency

as shown in the “Reference Frequency Selection” Table.

CLKSEL [Clock Select] TTL Input.

This input is used to select either the recovered clock of

the receiver PLL (CLKSEL = HIGH) or the clock of the

frequency synthesizer (CLKSEL = LOW) to the TCLK

outputs.

RDOUTP, RDOUTN [Receive Data Output] Differential

PECL.

These ECL 100K outputs (+3.3V or +5V referenced)

represent the recovered data from the input data stream

(RDIN). This recovered data is sampled on the rising edge

of RCLK.

RCLKP, RCLKN [Clock Output] Differential PECL.

These ECL 100K outputs (+3.3V or +5V referenced)

represent the recovered clock used to sample the recovered

data (RDOUT).

TCLKP, TCLKN [Clock Output] Differential PECL.

These ECL 100K outputs (+3.3V or +5V referenced)

represent either the recovered clock (CLKSEL = HIGH) used

to sample the recovered data (RDOUT) or the transmit clock

of the frequency synthesizer (CLKSEL = LOW).

PLLSP, PLLSN [Clock Synthesis PLL Loop Filter]

External loop filter pins for the clock synthesis PLL.

PLLRP, PLLRN [Clock Recovery PLL Loop Filter]

External loop filter pins for the receiver PLL.

POWER & GROUND

VCC

VCCA

VCCO

GND

N/C

Supply Voltage(Note 1)

Analog Supply Voltage(Note 1)

Output Supply Voltage(Note 1)

Ground

No Connect

Note 1. VCC, VCCA, VCCO must be the same value.

M9999-073008

hbwhelp@micrel.com or (408) 955-1690

3

Share Link: