STM705(2005) Просмотр технического описания (PDF) - STMicroelectronics

Номер в каталоге

Компоненты Описание

производитель

STM705
(Rev.:2005)

5V Supervisor

STMicroelectronics 

STM705/706/707/708/813L

OPERATION

Reset Output

The STM705/706/707/708/813L Supervisor as-

serts a reset signal to the MCU whenever VCC

goes below the reset threshold (VRST), a watch-

dog time-out occurs (if WDO is tied to MR), or

when the Push-button Reset Input (MR) is taken

low. RST is guaranteed to be a logic low (logic

high for STM707/708/813L) for VCC < VRST down

to VCC =1V for TA = 0°C to 85°C.

During power-up, once VCC exceeds the reset

threshold an internal timer keeps RST low for the

reset time-out period, trec. After this interval RST

returns high.

If VCC drops below the reset threshold, RST goes

low. Each time RST is asserted, it stays low for at

least the reset time-out period (trec). Any time VCC

goes below the reset threshold the internal timer

clears. The reset timer starts when VCC returns

above the reset threshold.

Push-button Reset Input

A logic low on MR asserts reset. Reset remains

asserted while MR is low, and for trec (see Figure

31., page 21) after it returns high. The MR input

has an internal 40kΩ pull-up resistor, allowing it to

be left open if not used. This input can be driven

with TTL/CMOS-logic levels or with open-drain/

collector outputs. Connect a normally open mo-

mentary switch from MR to GND to create a man-

ual reset function; external debounce circuitry is

not required. If MR is driven from long cables or

the device is used in a noisy environment, connect

a 0.1µF capacitor from MR to GND to provide ad-

ditional noise immunity. MR may float, or be tied to

VCC when not used.

Watchdog Input (STM705/706/813L)

The watchdog timer can be used to detect an out-

of-control MCU. If the MCU does not toggle the

Watchdog Input (WDI) within tWD (1.6sec), the re-

set is asserted. The internal 1.6sec timer is

cleared by either:

1. a reset pulse, or

2. by toggling WDI (high-to-low or low-to-high),

which can detect pulses as short as 50ns. If

WDI is tied high or low, a reset pulse is

triggered every 1.8sec (tWD + trec), if WDO is

connected to MR.

See Figure 32., page 21 for STM705/706/813L.

The timer remains cleared and does not count for

as long as reset is asserted. As soon as reset is re-

leased, the timer starts counting.

Note: The watchdog function may be disabled by

floating WDI or tri-stating the driver connected to

WDI. When tri-stated or disconnected, the maxi-

mum allowable leakage current is 10uA and the

maximum allowable load capacitance is 200pF.

Watchdog Output (STM705/706/813L)

When VCC drops below the reset threshold, WDO

will go low even if the watchdog timer has not yet

timed out. However, unlike the reset output, WDO

goes high as soon as VCC exceeds the reset

threshold. WDO may be used to generate a reset

pulse by connecting it to the MR input.

Power-fail Input/Output

The Power-fail Input (PFI) is compared to an inter-

nal reference voltage (independent from the VRST

comparator). If PFI is less than the power-fail

threshold (VPFI), the Power-Fail Output (PFO) will

go low. This function is intended for use as an un-

dervoltage detector to signal a failing power sup-

ply. Typically PFI is connected through an external

voltage divider (see Figure 10., page 8) to either

the unregulated DC input (if it is available) or the

regulated output of the VCC regulator. The voltage

divider can be set up such that the voltage at PFI

falls below VPFI several milliseconds before the

regulated VCC input to the STM705/706/707/708/

813L or the microprocessor drops below the mini-

mum operating voltage.

If the comparator is unused, PFI should be con-

nected to VSS and PFO left unconnected. PFO

may be connected to MR on the STM703/704/818

so that a low voltage on PFI will generate a reset

output.

9/27

Share Link: