MAS9138S Просмотр технического описания (PDF) - Micro Analog Systems Oy

Номер в каталоге

Компоненты Описание

производитель

MAS9138S

Asynchronous to synchronous converter

Micro Analog Systems Oy 

FUNCTIONS

u Asynchronous to synchronous converter

The synchronous start-stop character, TDI

(transmitter data input), is read into the Tx buffer.

When the character is available the data bits are

transferred as TDO (transmitter data output) with the

synchronous timing signal TXC (transmitter clock).

The bit rate of TDI must be the same as the TDO rate

within -2.5%...+1% or -2.5%...+2.3% tolerance

depending on XESR (extended signalling rate) signal.

The transmitter adds extra stop bits to the

synchronous data stream, if TDI is slower than TDO.

The over speed is handled by deleting one stop bit in

u Synchronous to asynchronous converter

The synchronous RDI (receiver data input) is buffered

to recognize the stop and start bits. If a missing stop

bit is detected, it is added to the RDO (receiver data

output). In this case the stop bits are shortened 12.5%

u Converting with higher speed timing

An alternative method to handle the over speed in

asynchronous data is to boost synchronous timing

TXC and RXC by 1-2%. In this mode XHST (higher

speed timing) = 0. In this case there is no need to

u Timing selection

The MAS9138 requires clock signals in order to

function properly. The synchronous data transfer

always requires the TXC clock. The clock is used

internally for:

-shifting data out from the TX buffer (to pin TDO)

-detection of the bit rate in order to adjust the internal

baud rate generator (only if TSL = 1)

The asynchronous data transfer (pins TDI, TDO) is

accomplished by generating an internal timing signal

for the asychronous circuits. This internal timing signal

(16T) is 16 times the TXC bit rate in order to sample

the asynchronous data stream (TDI) at the proper

DA9138.003

29 January, 2001

every 8th character at maximum in the synchronous

output data TDO. When extended signal rate (XESR =

0) is used 4th stop bit may be deleted. When the

transmitter detects a break signal( at least M bits of

start polarity, where M is length of character), it sends

2M + 3 bits of start - polarity to TDO. If the break is

longer than 2M + 3 bits, then all bits are transferred to

TDO. After a break signal, at least 2M bits of stop

polarity must be transmitted before sending further

data.

(25% if XESR = 0) during each character. When the

receiver gets at least 2M + 3 bits of start polarity, it

does not add stop bits to RDO. This enables the break

signal to go through the buffer.

delete any stop bits in the transmitter buffer. The

break signal goes through unchanged. On the receiver

side the synchronous data, RDI, is transferred directly

to the asynchronous output RDO with RXC.

speed. The internal clock 16T is either generated from

a crystal frequency by dividing it by 8, 16, 21 1/3, 25

3/5, 32, 42 2/3,64,128,256 or 512. Or it can also be

generated externally and fed to pin TMG (TSL = 0).

This is especially useful if the system already

generates a clock which is 16 times the bit clock TXC

as shown or if the bit rate is higher than 38.4 kHz. The

divider is automatically selected by internal logic by

measuring the TXC clock speed (TSL = 1). A crystal

oscillator or a resonator can also be connected

between pins 2 and 3. The crystal frequency should

be 128 x TXCmax.

Timing Circuits

16 x TXC

MAS 9138

TXC

EXTERNALLY GENERATED 16T CLOCK

u Character Length CL1,CL2

CL1

1

0

1

0

CL2

0

0

1

1

Conditions

8 bits

9 bits

10 bits

11 bits

6 (10)

Share Link: