SIP12502DMP-20-E3 Просмотр технического описания (PDF) - Vishay Semiconductors
Номер в каталоге
Компоненты Описание
производитель
SIP12502DMP-20-E3 Datasheet PDF : 11 Pages
| |||
Package Information
Vishay Siliconix
PowerPAKr MLP33-6, 8, 10
N = 6 PITCH: 0.95 mm
N = 8 PITCH: 0.65 mm
N = 10 PITCH: 0.50 mm
MILLIMETERS*
INCHES
Dim
Basic
Min
Nom
Max
Basic
Min
Nom
A
−
0.80
0.90
1.00
−
0.031
0.035
A1
−
0.00
0.025
0.05
−
0.000
0.001
A2
−
0.65
0.70
0.75
−
0.026
0.028
A3
−
0.15
0.20
0.25
−
0.006
0.008
aaa
−
−
0.10
−
−
−
0.004
b-6
−
0.33
0.35
0.43
−
0.013
0.014
b-8
−
0.285
0.305
0.385
−
0.011
0.012
b-10
−
0.18
0.20
0.28
−
0.007
0.008
bbb
−
−
0.10
−
−
−
0.004
ccc
−
−
0.10
−
−
−
0.004
D
3.00
−
−
−
0.118
−
−
D2
−
1.92
2.02
2.12
−
0.076
0.080
ddd
−
−
0.05
−
−
0.002
E
3.00
−
−
−
0.118
−
−
E2
−
1.10
1.20
1.30
−
0.043
0.047
e-6
−
−
0.95
−
−
−
0.037
e-8
−
−
0.65
−
−
−
0.026
e-10
−
−
0.50
−
−
−
0.020
K
−
0.20
−
−
−
0.008
−
L
−
0.20
0.29
0.45
−
0.008
0.011
L1-6
−
0.16
0.24
0.40
−
0.006
0.009
L1-8
−
0.16
0.24
0.40
−
0.006
0.009
L1-10
−
−
−
−
−
−
−
L2
−
R Ref
−
−
−
0.125
−
−
0.15
−
−
−
−
−
0.006
R1 Ref-6
−
−
0.127
−
−
−
0.005
R1 Ref-8
−
−
0.15
−
−
−
0.006
R1 Ref-10
−
−
0.075
−
−
−
0.003
Q
−
0_
10_
12_
−
0_
10_
* Use millimeters as the primary measurement.
ECN: S-40082—Rev. A, 02-Feb-04
DWG: 5925
Max
0.039
0.002
0.030
0.010
−
0.017
0.015
0.011
−
−
−
0.083
−
0.051
−
−
−
−
0.018
0.016
0.016
−
0.005
−
−
−
−
12_
Notes
1, 2
1, 2
1, 2
1, 2
1, 2
1, 2, 8
1, 2, 8
1, 2, 8
1, 2
1, 2
1, 2, 8
1, 2, 8
1, 2
1, 2, 8
1, 2, 8
1, 2
1, 2
1, 2
5, 11
1, 2, 8
1, 2, 8
1, 2, 8
1, 2, 8
5, 11
1, 2, 8
1, 2, 8
1, 2, 8
1, 2, 8
1, 2
NOTES:
1. Dimensioning and tolerancing conform to ASME Y14.5M-1994.
2. All dimensions are in millimeters. All angels are in degrees.
3. N is the total number of pins.
4. The pin #1 identifier and pin numbering convention shall conform to JESD 95-1 SPP-012. Details of pin #1 identifier is located within the
zone indicated. The pin #1 identifier is marked.
5. Dimension b applies to metallized pin and is measured between 0.15 mm and 0.20 mm from the pin tip.
6. ND refers to the maximum number of pins on the D side.
7. Depopulation of pins is allowed and will be called out on the individual variation.
8. Coplanarity applies to the exposed heat sink slug as well as the pins.
9. Profile tolerance (aaa) will be applicable only to the plastic body and not to the metallized features (such as the pin tips and tie bars.)
Metallized features may protrude a maximum of L2 from the plastic body profile.
10. L1 max is not called out, the metallized feature will extend to the exposed pad. Thus, the 0.17-mm gap does not apply.
11. The corner will be sharp unless otherwise specified with radius dimensions.
www.vishay.com
2
Document Number: 72820
28-Jan-04
Share Link: 