SI3016 Просмотр технического описания (PDF) - Silicon Laboratories
Номер в каталоге
Компоненты Описание
производитель
SI3016 Datasheet PDF : 50 Pages
| |||
Si3016
2. Bill of Materials
Table 7. Si3016 Global Component Values
Component
Value
Supplier(s)
C1,C41
150 pF, 3 kV, X7R,±20%
Novacap, Venkel, Johanson, Murata, Panasonic
C2, C31, C32
C3, C132
Not Installed
0.22 µF, 16 V, X7R, ±20%
C5
0.1 µF, 50 V, Elec/Tant, ±20%
C6,C16
0.1 µF, 16 V, X7R, ±20%
C7,C8
560 pF, 250 V, X7R, ±20%
Novacap, Johanson, Murata, Panasonic
C9
10 nF, 250 V, X7R, ±20%
C12
1.0 µF, 16 V, Tant, ±20%
Panasonic
C14
0.68 µF, 16 V, X7R/Elec/Tant, ±20%
C18,C19
3.9 nF, 16 V, X7R, ±20%
C20
0.01 µF, 16 V, X7R, ±20%
C22
C24,C251
C303
D1,D24
1800 pF, 50 V, X7R, ±20%
1000 pF, 3 kV, X7R, ±10%
Not Installed
Dual Diode, 300 V, 225 mA
Central Semiconductor
D3,D4
BAV99 Dual Diode, 70 V, 350 mW
Diodes Inc., OnSemiconductor, Fairchild
FB1,FB2
L1, L25
Ferrite Bead
330 μH, DCR < 3 Ω, 120 mA, ±10%
Murata
Taiyo-Yuden, ACT, Transtek Magnetics, Cooper Electronics
Q1,Q3
A42, NPN, 300 V
OnSemiconductor, Fairchild
Q2
A92, PNP, 300 V
Q46
BCP56T1, NPN, 80 V, 1/2 W
OnSemiconductor, Fairchild
OnSemiconductor, Fairchild
RV1
RV27
R28
Sidactor, 275 V, 100 A
Not Installed
402 Ω, 1/16 W, ±1%
Teccor, ST Microelectronics, Microsemi, TI
R5
100 kΩ, 1/16 W, ±1%
R6
R7,R8,R15,R16,R17,R199
120 kΩ, 1/16 W, ±5%
5.36 kΩ, 1/4 W, ±1%
R9,R10
56 kΩ, 1/10 W, ±5%
R11
9.31 kΩ, 1/16 W, ±1%
R12
78.7 Ω, 1/16 W, ±1%
R13
215 Ω, 1/16 W, ±1%
R18
2.2 kΩ, 1/10 W, ±5%
R24
150 Ω, 1/16 W, ±5%
R25,R26
10 MΩ, 1/16 W, ±5%
R27,R28
10 Ω, 1/10 W, ±5%
U1
Si3021
Silicon Labs
U2
Silicon Labs System-Side Device
Silicon Labs
Z1
Zener Diode, 43 V, 1/2 W
Vishay, Motorola, Rohm
Z4,Z5
Zener Diode, 5.6 V, 1/2 W
Vishay, Motorola, Rohm
Notes:
1. Y2 class capacitors are needed for the Nordic requirements of EN60950 and may also be used to achieve surge performance of 5 kV or better.
2. C13 is used to ensure compliance with on-hook pulse dialing and spark quenching requirements in countries, such as Australia and South Africa. If this
is not a concern, a 0.1 µF cap may be used.
3. Install only if needed for improved radiated emissions performance (10 pF, 16 V, NPO, ±10%).
4. Several diode bridge configurations are acceptable (suppliers include General Semi., Diodes Inc.).
5. See Appendix B for additional requirements.
6. Q4 may require copper on board to meet 1/2 W power requirement. (Contact manufacturer for details.)
7. RV2 can be installed to improve performance from 2500 V to 3500 V for multiple longitudinal surges (270 V, MOV).
8. If supporting +3.2 dBFS voice applications, R2 should be 243 Ω and set the FULLSCALE bit (Reg 18[7]).
9. The R7, R8, R15, and R16, R17, and R19 resistors may each be replaced with a single resistor of 1.62 kΩ, 3/4 W, ±1%.
10
Rev. 1.0
Share Link: 