DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

SI3016-BS Просмотр технического описания (PDF) - Unspecified

Номер в каталоге
Компоненты Описание
производитель
SI3016-BS Datasheet PDF : 48 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Si3016
Table 3. DC Characteristics
(TA = 0 to 70 °C for K-Grade and –40 to 85 °C for B-Grade)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Input Leakage Current
IL
–10
10
µA
Power Supply Current, Analog*
IA
0.3
mA
*Note: This current is required from the integrated system-side interface to communicate with the Si3016 through the ISOcap
interface.
Table 4. AC Characteristics
(TA = 0 to 70 °C for K-Grade and –40 to 85 °C for B-Grade, see Figure 6 on page 9)
Parameter
Symbol
Test Condition
Min
Typ Max Unit
Sample Rate
Transmit Frequency Response
Fs
Fs = FPLL2/5120
7.2
— 11.025 KHz
Low –3 dBFS Corner
0
Hz
Receive Frequency Response
Low –3 dBFS Corner
5
Hz
Transmit Full Scale Level1
Receive Full Scale Level1,3
Dynamic Range4,5,6
Dynamic Range4,5,7
Dynamic Range4,5,6
Transmit Total Harmonic Distortion6,8
Transmit Total Harmonic Distortion7,8
Receive Total Harmonic Distortion7,8
Receive Total Harmonic Distortion6,8
VFS
FULL = 0 (–1 dBm)
FULL = 1 (+3.2 dBm)2
VFS
FULL = 0 (–1 dBm)
FULL = 1 (+3.2 dBm)3
DR ACT=0, DCT=10 (FCC) —
IL=100 mA
DR ACT=0, DCT=01 (Japan) —
IL=20 mA
DR ACT=1, DCT=11(CTR21) —
IL=60 mA
THD ACT=0, DCT=10 (FCC) —
IL=100 mA
THD ACT=0, DCT=01 (Japan) —
IL=20 mA
THD ACT=0, DCT=01 (Japan) —
IL=20 mA
THD ACT=1, DCT=11 (CTR21) —
IL=60 mA
1
1.58
1
1.58
82
83
84
–85
–76
–74
–82
— VPEAK
— VPEAK
— VPEAK
— VPEAK
dB
dB
dB
dB
dB
dB
dB
Dynamic Range (Caller ID mode)
DRCID VIN = 1 kHz, –13 dBm
60
dB
Notes:
1. Measured at TIP and RING with 600 termination at 1 kHz, as shown in Figure 1.
2. R2 should be changed to a 243 resistor when the FULLSCALE bit (FULL) is set to 1 (Register 18, bit 7).
3. Receive full scale level will produce –0.9 dBFS at SDO.
4. DR = 20 x log |Vin| + 20 x log (RMS signal/RMS noise).
5. Measurement is 300 to 3400 Hz. Applies to both transmit and receive paths.
6. Vin = 1 kHz, –3 dBFS, Fs = 10300 Hz.
7. Vin = 1 KHz, –6 dBFS, Fs = 10300 Hz.
8. THD = 20 x log (RMS distortion/RMS signal).
9. The AOUT pin is an optional pin located on the integrated system side module. VD refers to the digital power supply of
the integrated system side module.
6
Rev. 0.44

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]