PI5C3390 Просмотр технического описания (PDF) - Pericom Semiconductor
Номер в каталоге
Компоненты Описание
производитель
PI5C3390 Datasheet PDF : 4 Pages
| |||
PI5C3390; PI5C32390
16:8 Multiplexer/Demultiplexer
Bus Switch 1122334455667788990011223344556677889900112233445566778899001122112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900112233445566778899001122112233445566778899001122
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature .......................................................... –65°C to +150°C
Ambient Temperature with Power Applied .......................... –40°C to +85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) .... –0.5V to +7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only) . –0.5V to +7.0V
DC Input Voltage ................................................................... –0.5V to +7.0V
DC Output Current ............................................................................. 120 mA
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device. This
is a stress rating only and functional operation
of the device at these or any other conditions above those
indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect reliability.
Power Dissipation ................................................................................... 0.5W
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5V ±5%)
Parameters Description
Test Conditions(1)
Min.
VIH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0
VIL
Input LOW Voltage
Guaranteed Logic LOW Level
–0.5
IIH
Input HIGH Current
VCC = Max., VIN = VCC
—
IIL
Input LOW Current
VCC = Max., VIN = GND
—
IOZH
High Impedance Output Current 0 ≤ A, B, C ≤ VCC
—
VIK
Clamp Diode Voltage
VCC = Min., IIN = –18 mA
IOS
Short Circuit Current(3)
A, B (C) = 0V, C (A, B) = VCC
100
VH
Input Hysteresis at Control Pins
—
RON
Switch On Resistance(4)
VCC = Min., VIN = 0.0V,
PI5C3390
—
ION = 48 mA
PI5C32390
20
VCC = Min., VIN = 2.4V,
PI5C3390
—
ION = 15 mA
PI5C32390
20
Typ(2)
—
—
—
—
—
–0.7
—
150
5
28
10
35
Max.
—
0.8
±1
±1
±1
–1.2
—
—
7
40
15
48
Units
V
V
µA
µA
µA
V
mA
mV
ohm
ohm
Capacitance (TA = 25°C, f = 1 MHz)
Parameters(5)
Description
CIN
Input Capacitance
COFF
A/B Capacitance, Switch Off
CON
A/B Capacitance, Switch On
Test Conditions
VIN = 0V
VIN = 0V
VIN = 0V
Typ Units
6
pF
6
pF
8
pF
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at Vcc= 5.0V, TA = 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A, B, and C pins at indicated current through the switch. On-Resistance is determined by the lower of
the voltages on the two (A,B,C) pins.
5. This parameter is determined by device characterization but is not production tested.
2
PS7030E 09/15/04
Share Link: 