MCM6726C Просмотр технического описания (PDF) - Motorola => Freescale
Номер в каталоге
Компоненты Описание
производитель
MCM6726C Datasheet PDF : 7 Pages
| |||
TRUTH TABLE (X = Don’t Care)
E
G
W
Mode
H
X
X
Not Selected
L
H
H Output Disabled
L
L
H
Read
L
X
L
Write
VCC Current
ISB1, ISB2
ICCA
ICCA
ICCA
Output
High–Z
High–Z
Dout
High–Z
Cycle
—
—
Read Cycle
Write Cycle
ABSOLUTE MAXIMUM RATINGS (See Note)
Rating
Symbol
Value
Unit
Power Supply Voltage
VCC
– 0.5 to + 7.0
V
Voltage Relative to VSS for Any Pin Except Vin, Vout – 0.5 to VCC + 0.5 V
VCC
Output Current
Iout
± 30
mA
Power Dissipation
PD
1.5
W
Temperature Under Bias
Tbias
– 10 to + 85
°C
Operating Temperature
TA
0 to + 70
°C
Storage Temperature — Plastic
Tstg
– 55 to + 125
°C
NOTE: Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are
exceeded. Functional operation should be restricted to RECOMMENDED OPER-
ATING CONDITIONS. Exposure to higher than recommended voltages for
extended periods of time could affect device reliability.
This device contains circuitry to protect the
inputs against damage due to high static volt-
ages or electric fields; however, it is advised
that normal precautions be taken to avoid appli-
cation of any voltage higher than maximum
rated voltages to these high–impedance cir-
cuits.
This BiCMOS memory circuit has been de-
signed to meet the dc and ac specifications
shown in the tables, after thermal equilibrium
has been established. The circuit is in a test
socket or mounted on a printed circuit board
and transverse air flow of at least 500 linear feet
per minute is maintained.
DC OPERATING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V ± 10%, TA = 0 to 70°C, Unless Otherwise Noted)
RECOMMENDED OPERATING CONDITIONS
Parameter
Symbol
Min
Supply Voltage (Operating Voltage Range)
Input High Voltage
VCC
4.5
VIH
2.2
Input Low Voltage
VIL
– 0.5*
** VIL (min) = –0.5 V dc; VIL (min) = –2.0 V ac (pulse width ≤ 2.0 ns) for I ≤ 20.0 mA.
** VIH (max) = VCC + 0.3 V dc; VIH (max) = VCC + 2 V ac (pulse width ≤ 2.0 ns) for I ≤ 20.0 mA.
DC CHARACTERISTICS
Parameter
Input Leakage Current (All Inputs, Vin = 0 to VCC)
Output Leakage Current (E = VIH, Vout = 0 to VCC)
Output Low Voltage (IOL = + 8.0 mA)
Output High Voltage (IOH = – 4.0 mA)
Symbol
Ilkg(I)
Ilkg(O)
VOL
VOH
Typ
Max
Unit
5.0
5.5
V
—
VCC + 0.3** V
—
0.8
V
Min
Max
Unit
—
± 1.0
µA
—
± 1.0
µA
—
0.4
V
2.4
—
V
POWER SUPPLY CURRENTS
Parameter
Symbol MCM6726C–6 MCM6726C–7 Unit
AC Active Supply Current (Iout = 0 mA) (VCC = max, f = fmax)
ICCA
250
220
mA
Active Quiescent Current (E = VIL, VCC = max, f = 0 MHz)
ICC2
100
100
mA
AC Standby Current (E = VIH, VCC = max, f = fmax)
ISB1
100
100
mA
CMOS Standby Current (VCC = max, f = 0 MHz, E ≥ VCC – 0.2 V,
Vin ≤ VSS + 0.2 V, or ≥ VCC – 0.2 V)
ISB2
60
60
mA
NOTES:
1. Reference AC Operating Conditions and Characterisitics for input and timing (VIH/VIL, tr/tf, pulse level 0 to 3 V, VIH = 3 V).
2. All addresses transition simultaneously low (LSB) and then high (MSB).
3. Data States are all zero.
Notes
1, 2, 3
1, 2, 3
MCM6726C
2
MOTOROLA FAST SRAM
Share Link: 