MC100EL13
Table 4. 100EL SERIES PECL DC CHARACTERISTICS VCC = 5.0 V; VEE = 0.0 V (Note 2)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
IIH
IIL
Power Supply Current
30
38
30
38
32
40 mA
Output HIGH Voltage (Note 3)
3915 3995 4120 3975 4045 4120 3975 4050 4120 mV
Output LOW Voltage (Note 3)
3170 3305 3445 3190 3295 3380 3190 3295 3380 mV
Input HIGH Voltage (Single−Ended)
3835
4120 3835
4120 3835
4120 mV
Input LOW Voltage (Single−Ended)
3190
3525 3190
3525 3190
3525 mV
Output Voltage Reference
3.62
3.74 3.62
3.74 3.62
3.74 V
Common Mode Range
(Differential Configuration) (Note 4)
VPP < 500 mV 1.3
VPP ≥ 500 mV 1.5
Input HIGH Current
4.6 1.2
4.6 1.4
150
4.6 1.2
4.6 1.4
150
V
4.6
4.6
150 mA
Input LOW Current
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
2. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / −0.5 V.
3. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
4. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 5. 100EL SERIES NECL DC CHARACTERISTICS VCC = 0.0 V; VEE = −5.0 V (Note 5)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Power Supply Current
30
38
30
38
32
40 mA
VOH
Output HIGH Voltage (Note 6)
−1085 −1005 −880 −1025 −955 −880 −1025 −955 −880 mV
VOL
Output LOW Voltage (Note 6)
−1830 −1695 −1555 −1810 −1705 −1620 −1810 −1705 −1620 mV
VIH
Input HIGH Voltage (Single−Ended) −1165
−880 −1165
−880 −1165
−880 mV
VIL
Input LOW Voltage (Single−Ended) −1810
−1475 −1810
−1475 −1810
−1475 mV
VBB
Output Voltage Reference
−1.38
−1.26 −1.38
−1.26 −1.38
−1.26 V
VIHCMR
Common Mode Range
(Differential Configuration) (Note 7)
VPP < 500 mV
VPP ≥ 500 mV
−3.7
−3.5
−0.4 −3.8
−0.4 −3.6
−0.4 −3.8
−0.4 −3.6
V
−0.4
−0.4
IIH
Input HIGH Current
150
150
150 mA
IIL
Input LOW Current
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
5. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / −0.5 V.
6. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
7. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
3