LT1576CS8-SYNC Просмотр технического описания (PDF) - Linear Technology
Номер в каталоге
Компоненты Описание
производитель
LT1576CS8-SYNC Datasheet PDF : 28 Pages
| |||
LT1576/LT1576-5
ELECTRICAL CHARACTERISTICS The q denotes specifications which apply over the full operating temperature
range, otherwise specifications are TA, TJ = 25°C, VIN = 15V, VC = 1.5V, Boost = VIN + 5V, switch open, unless otherwise noted.
PARAMETER
Minimum Switch Duty Cycle (Note 10)
Switch Frequency
Switch Frequency Line Regulation
Frequency Shifting Threshold on FB Pin
Minimum Input Voltage (Note 3)
Minimum Boost Voltage (Note 4)
Boost Current (Note 5)
VIN Supply Current (Note 6)
BIAS Supply Current (Note 6)
Shutdown Supply Current
Lockout Threshold
Shutdown Thresholds
Synchronization Threshold
Synchronizing Range
SYNC Pin Input Resistance
CONDITIONS
VC Set to Give 50% Duty Cycle
5V ≤ VIN ≤ 25V
∆f = 10kHz
ISW ≤ 1.5A
ISW = 0.5A
ISW = 1.5A
VBIAS = 5V
VBIAS = 5V
VSHDN = 0V, VIN ≤ 25V, VSW = 0V, VC Open
VC Open
VC Open Device Shutting Down
Device Starting Up
MIN TYP MAX
8
180 200 220
q 160
240
q
0 0.15
q 0.4 0.74 1.0
q
5.0 5.5
q
2.3 3.0
q
9
18
q
27 50
q
0.55 0.8
q
1.6 2.2
20 50
q
75
q 2.34 2.42 2.50
q 0.13 0.37 0.60
q 0.25 0.45 0.7
1.5 2.2
250
400
40
UNITS
%
kHz
kHz
%/ V
V
V
V
mA
mA
mA
mA
µA
µA
V
V
V
V
kHz
kΩ
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: Gain is measured with a VC swing equal to 200mV above the
switching threshold level to 200mV below the upper clamp level.
Note 3: Minimum input voltage is not measured directly, but is guaranteed
by other tests. It is defined as the voltage where internal bias lines are still
regulated so that the reference voltage and oscillator frequency remain
constant. Actual minimum input voltage to maintain a regulated output will
depend on output voltage and load current. See Applications Information.
Note 4: This is the minimum voltage across the boost capacitor needed to
guarantee full saturation of the internal power switch.
Note 5: Boost current is the current flowing into the boost pin with the pin
held 5V above input voltage. It flows only during switch on time.
Note 6: VIN supply current is the current drawn when the BIAS pin is held
at 5V and switching is disabled. Total input referred supply current is
calculated by summing input supply current (ISI) with a fraction of BIAS
supply current (ISB)
ITOT = ISI + (ISB)(VBIAS/VIN)(1.15)
with VIN = 15V, VBIAS = 5V, ISI = 0.55mA, ISB = 1.6mA and ITOT = 1.16mA.
If the BIAS pin is unavailable or open circuit, the sum of VIN and BIAS
supply currents will be drawn by the VIN pin.
Note 7: Switch on resistance is calculated by dividing VIN to VSW voltage
by the forced current (1.5A). See Typical Performance Characteristics for
the graph of switch voltage at other currents.
Note 8: Transconductance and voltage gain refer to the internal amplifier
exclusive of the voltage divider. To calculate gain and transconductance,
refer to the SENSE pin on the fixed voltage parts. Divide values shown by
the ratio VOUT/1.21.
Note 9: Slope compensation is the current subtracted from the switch
current limit at 80% duty cycle. See Maximum Output Load Current in the
Applications Information section for further details.
Note 10: Minimum on-time is 400ns typical. For a 200kHz operating
frequency this means the minimum duty cycle is 8%. In frequency
foldback mode, the effective duty cycle will be less than 8%.
3
Share Link: 