LPC2292 Просмотр технического описания (PDF) - NXP Semiconductors.
Номер в каталоге
Компоненты Описание
производитель
LPC2292
NXP Semiconductors.
LPC2292 Datasheet PDF : 54 Pages
| |||
NXP Semiconductors
LPC2292/LPC2294
16/32-bit ARM microcontrollers with external memory interface
Table 4. Pin description …continued
Symbol
Pin (LQFP) Pin
(TFBGA)[1]
P0[27]/AIN0/ 23[6]
CAP0[1]/
MAT0[1]
H3[6]
P0[28]/AIN1/ 25[6]
J1[6]
CAP0[2]/
MAT0[2]
P0[29]/AIN2/ 32[6]
CAP0[3]/
MAT0[3]
L1[6]
P0[30]/AIN3/ 33[6]
EINT3/CAP0[0]
L2[6]
P1[0] to P1[31]
Type
I
I
O
I
I
O
I
I
O
I
I
I
I/O
P1[0]/CS0
91[7]
P1[1]/OE
P1[16]/
TRACEPKT0
P1[17]/
TRACEPKT1
P1[18]/
TRACEPKT2
P1[19]/
TRACEPKT3
P1[20]/
TRACESYNC
90[7]
34[7]
24[7]
15[7]
7[7]
102[7]
P1[21]/
PIPESTAT0
P1[22]/
PIPESTAT1
P1[23]/
PIPESTAT2
P1[24]/
TRACECLK
95[7]
86[7]
82[7]
70[7]
G11[7]
O
G13[7]
O
L3[7]
O
H4[7]
O
F2[7]
O
D2[7]
O
D12[7]
O
F11[7]
O
H11[7]
O
J11[7]
O
L11[7]
O
Description
AIN0 — ADC, input 0. This analog input is always connected
to its pin.
CAP0[1] — Capture input for Timer 0, channel 1.
MAT0[1] — Match output for Timer 0, channel 1.
AIN1 — ADC, input 1. This analog input is always connected
to its pin.
CAP0[2] — Capture input for Timer 0, channel 2.
MAT0[2] — Match output for Timer 0, channel 2.
AIN2 — ADC, input 2. This analog input is always connected
to its pin.
CAP0[3] — Capture input for Timer 0, Channel 3.
MAT0[3] — Match output for Timer 0, channel 3.
AIN3 — ADC, input 3. This analog input is always connected
to its pin.
EINT3 — External interrupt 3 input.
CAP0[0] — Capture input for Timer 0, channel 0.
Port 1: Port 1 is a 32-bit bidirectional I/O port with individual
direction controls for each bit. The operation of port 1 pins
depends upon the pin function selected via the Pin Connect
Block.
Pins 2 through 15 of port 1 are not available.
CS0 — LOW-active Chip Select 0 signal.
(Bank 0 addresses range 0x8000 0000 to 0x80FF FFFF)
OE — LOW-active Output Enable signal.
TRACEPKT0 — Trace Packet, bit 0. Standard I/O port with
internal pull-up.
TRACEPKT1 — Trace Packet, bit 1. Standard I/O port with
internal pull-up.
TRACEPKT2 — Trace Packet, bit 2. Standard I/O port with
internal pull-up.
TRACEPKT3 — Trace Packet, bit 3. Standard I/O port with
internal pull-up.
TRACESYNC — Trace Synchronization. Standard I/O port
with internal pull-up.
Note: LOW on this pin while RESET is LOW, enables pins
P1[25:16] to operate as Trace port after reset.
PIPESTAT0 — Pipeline Status, bit 0. Standard I/O port with
internal pull-up.
PIPESTAT1 — Pipeline Status, bit 1. Standard I/O port with
internal pull-up.
PIPESTAT2 — Pipeline Status, bit 2. Standard I/O port with
internal pull-up.
TRACECLK — Trace Clock. Standard I/O port with internal
pull-up.
LPC2292_2294_6
Product data sheet
Rev. 06 — 10 December 2007
© NXP B.V. 2007. All rights reserved.
10 of 54
Share Link: