LB11990W Просмотр технического описания (PDF) - SANYO -> Panasonic
Номер в каталоге
Компоненты Описание
производитель
LB11990W Datasheet PDF : 14 Pages
| |||
LB11990W
Cylinder Motor Driver Block at Ta = 25°C, VCC1 = 3V, VCC2 = 4.75V, VS = 3V
Parameter
Symbol
Conditions
Ratings
min typ max
Unit
Power supply current 4
ICC2 IO = 76 mA VSTBY_D = 3V VSTBY_C = 0V
0.75 2.5 mA
Output idle current 4
ICC2Q VSTBY D = VSTBY_C = 0V
100 µA
Output idle current 5
IS(D)Q VSTBY D = VSTBY_C = 0V
100 300 µA
Output saturation voltage, upper side 1 VOU1 IO = 0.1A RF = 0.25Ω
0.3 0.5
V
Output saturation voltage, lower side 1 VOD1 IO = 0.1A RF = 0.25Ω
0.3 0.5
V
Output saturation voltage, upper side 2 VOU2 IO = 0.4A, VS = 3V RF = 0.25Ω
0.5 0.8
V
Output saturation voltage, lower side 2 VOD2 IO = 0.4A, VS = 3V RF = 0.25Ω
0.5 0.8
V
COM pin common mode input voltage range
Standby pin High level voltage
Standby pin Low level voltage
VIC
VSTBYH
VSTBYL
0.3
2
–0.2
VCC2–0.9
V
VCC1
V
+0.7
V
Standby pin input current
ISTBYH VSTBY_D = 3V
50 µA
Standby pin leakage current
ISTBYL VSTBY_D = 0V
–10
µA
FRC pin High level voltage
FRC pin Low level voltage
VFRCH
VFRCL
2
VCC1
V
–0.2
+0.7
V
FRC pin input current
IFRCI VFRC_D = 3V
50 µA
FRC pin leakage current
IFRCL VFRC_D = 0V
–10
µA
Slope pin source current ratio
RSOURCE ICSLP1SOURCE/ICSLP2SOURCE
–15
+15 %
Slope pin sink current ratio
RSINK ICSLP1SINK/ICSLP2SINK
–15
+15 %
CSLP1 source/sink current ratio
RCSLP1 ICSLP1SOURCE/ICSLP1SINK
–35
+15 %
CSLP2 source/sink current ratio
RCSLP2 ICSLP2SOURCE/ICSLP2SINK
–35
+15 %
Startup frequency
Freq Cosc = 0.1 µF, OSC frequency (Target)
11.5
Hz
Phase delay-width
Dwidth (Target)
30
deg
SELCSLP pin High level voltage
SELCSLP pin Low level voltage
VSELH
VSELL
2
VCC1
V
–0.2
+0.7
V
SELCSLP pin input current
ISELH VSELCSLP = 3V
50 µA
SELCSLP pin leakage current
ISELL VSELCSLP = 0V
–10
µA
Note) Items shown to be “Target” are not measured.
FG/PG Amplifier Block at Ta = 25°C, VCC1 = 3V, VCC2 = 4.75V, VS = 3V
Parameter
Symbol
Conditions
[FG amplifier]
Input offset voltage
Input bias current
Common mode input voltage range
Open loop gain
Output ON voltage
Output OFF voltage
Schmitt amplifier hysteresis width
Reference voltage
[PG amplifier]
Input offset voltage
Input bias current
Common mode input voltage range
Open loop gain
Output ON voltage
Output OFF voltage
Schmitt amplifier hysteresis width
VIO
IBIN–
VICOM
GVFG
VOL
VOH
VSHIS
VREF
(Target)
(Target)
(Target)
f = 1 kHz (Target)
At IO = 10 µA
At IO = 10 µA
(Target)
VIO
IBIN–
VICOM
GVPG
VOL
VOH
VSHIS
(Target)
(Target)
(Target)
f = 1 kHz (Target)
At IO = 10 µA
At IO = 10 µA
(Target)
Note) Items shown to be “Target” are not measured.
Ratings
min typ max
Unit
±1
±5 mA
250 nA
1
2
V
55
dB
0.4
V
VCC1–0.5
V
50
mV
1.15 1.30 1.45
V
1
VCC1–0.5
±1
±5 mV
250 nA
2
V
55
dB
0.4
V
V
50
mV
No. 6216-3/14
Share Link: 