HCPL-3180-000 Просмотр технического описания (PDF) - HP => Agilent Technologies
Номер в каталоге
Компоненты Описание
производитель
HCPL-3180-000
HP => Agilent Technologies
HCPL-3180-000 Datasheet PDF : 19 Pages
| |||
Switching Specifications (AC)
Over recommended operating conditions unless otherwise specified.
Parameter
Propagation Delay Time to High Output Level
Symbol
tPLH
Min Typ
50
150
Propagation Delay Time to Low Output Level
tPHL
50
150
Pulse Width Distortion
PWD
20
Propagation Delay Difference Between Any Two
Parts
PDD
-90
(tPHL - tPLH)
Rise Time
tr
25
Fall Time
UVLO Turn On Delay
UVLO Turn Off Delay
Output High Level Common Mode Transient
Immunity
tf
tUVLO ON
tUVLO OFF
|CMH|
25
2.0
0.3
10
Output Low Level Common Mode Transient
Immunity
|CML|
10
Max
200
200
65
90
Units Test Conditions Fig Note
ns
IF = 10 mA
Rg = 10 W
f = 250 kHz
10, 16
11,
12,
ns
Duty Cycle = 50% 13,
Cg = 10 nF
14,
23
ns
12
ms
35, 17
36
ns
CL = 1 nF
23
Rg = 0 W
ns
us
22
us
kV/µs
kV/µs
TA = +25 °C
If = 10 to 16 mA
VCM = 1.5 kV
VCC = 20 V
TA = +25 °C
Vf = 0 V
VCM = 1.5 kV
VCC = 20 V
VCM = 1.5 kV
24 13, 14
13, 15
Package Characteristics
Parameter
Input-Output Momentary Withstand Voltage
Input-Output Resistance
Input-Output Capacitance
Symbol
VISO
RI-O
CI-O
Min Typ Max Units Test Conditions Fig Note
2500
Vrms
TA = +25 °C,
8, 9
RH < 50%
1011
W
VI-O = 500 V
9
1
pF
Freq = 1 MHz
Notes:
1. Derate linearly above +70 °C free air temperature at a rate of 0.3 mA/°C.
2. Maximum pulse width = 10 us, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with IO peak
minimum = 2.0 A. See Application section for additional details on limiting IOL peak.
3. Derate linearly above +70 °C, free air temperature at the rate of 4.8 mW/°C.
4. Derate linearly above +70 °C, free air temperature at the rate of 5.4 mW/°C. The maximum LED junction temperature should not exceed +125 °C.
5. Maximum pulse width = 50 us, maximum duty cycle = 0.5%.
6. In this test, VOH is measured with a dc load current. When driving capacitive load VOH will approach VCC as IOH approaches zero amps.
7. Maximum pulse width = 1 ms, maximum duty cycle = 20%.
8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 3000 Vrms for 1 second (leakage detection
current limit II-O < 5 uA).
9. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together.
10. tPHL propagation delay is measured from the 50% level on the falling edge of the input pulse to the 50% level of the falling edge of the VO signal. tPLH
propagation delay is measured from the 50% level on the rising edge of the input pulse to the 50% level of the rising edge of the VO signal
11. tPSK is equal to the magnitude of the worst case difference in tPHL and/or tPLH that will be seen between units at any given temperature within the
recommended operating conditions
12. PWD is defined as |tPHL - tPLH | for any given device.
13. Pin 1 and 4 need to be connected to LED common.
7
Share Link: