GS9015BCPJ Просмотр технического описания (PDF) - Gennum -> Semtech

Номер в каталоге

Компоненты Описание

производитель

GS9015BCPJ

Serial Digital Reclocker

Gennum -> Semtech 

Temperature Compensation

Figure 14 shows the connections for the frequency setting

resistors for the various data rates. The compensation shown

for 360 Mb/s and 177 Mb/s with Divide by 2 ON, is useful to

a maximum ambient temperature of 50°C. If the Divide by 2

function is not enabled by the ƒ/2 ENABLE input, no

compensation is needed for the 143 Mb/s and 177 Mb/s data

rates. The resistor connections are shown in Figure 15. In

both cases , the 0.1µF capacitor that bypasses the

potentiometer should be star routed to VEE3.

1k

5k

0.1µF

VEE

Divide by 2 is OFF

5.6k

1.3k

D 1N914

E 5k

0.1µF

4.3k

1.3k

1N914

5k

0.1µF

ND S VEE

VEE

Divide by 2 is OFF

Divide by 2 is ON

E N 270 Mb/s using RVCO0 or RVCO1 143 Mb/s using RVCO2 or RVCO3

M IG 1k

1k

M S 1k

1k

O E 0.1µF

0.1µF

C D 1N914

1N914

VEE

E Divide by 2 is OFF

VEE

Divide by 2 is ON

R W 360 Mb/s using RVCO0 or RVCO1 177 Mb/s using RVCO2 or RVCO3

E Fig. 14 Frequency Setting Resistor Values

T & Temperature Compensation

N Temperature Compensation Procedure

NO R In order to correctly set the VCO frequency so that the PLL will

always re-acquire lock over the full temperature range, the

following procedure should be used. The circuit should be

O powered on for at least one minute prior to starting this

F procedure.

143Mb/s and 177 Mb/s using any RVCO pins

Fig. 15 Non - Temperature Compensated Resistor Values

for 143 Mb/s and 177 Mb/s

Loop Bandwidth

The loop bandwidth is dependant upon the internal PLL gain

constants along with the loop filter components connected to

pin 12. In addition, the impedance seen by the RVCO pin also

influences the loop characteristics such that as the imped-

ance drops, the loop gain increases.

Applications Circuit

Figure 16 shows an application of the GS9015B in an

adjustment free, multi-standard serial to parallel convertor.

This circuit uses the GS9010A Automatic Tuning Sub-

system IC and a GS9000B or GS9000S Decoder IC.

The GS9010A ATS eliminates the need to manually set or

externally temperature compensate the Receiver or Reclocker

VCO. The GS9010A can also determine whether the

incoming data stream is 4ƒsc NTSC,4ƒsc PAL or component

4:2:2.

The GS9010A includes a ramp generator/oscillator which

repeatedly sweeps the Reclocker VCO frequency over a

set range until the system is correctly locked. An automatic

fine tuning (AFT) loop maintains the Reclocker VCO control

voltage at it's centre point through continuous, long term

adjustments of the VCO centre frequency.

During normal operation, the GS9000B or GS9000S Decoder

provides continuous HSYNC pulses which disable the

ramp/oscillator of the GS9010A. This maintains the

Monitor the loop filter voltage at the junction of the loop filter

resistor and 10 nF loop filter capacitor (LOOP FILTER TEST

POINT). Using the appropriate network shown above, the

VCO frequency is set by first tuning the potentiometer so that

the PLL loses lock at the low end (lowest loop filter voltage).

The loop filter voltage is then slowly increased by adjusting the

correct Reclocker VCO frequency. When an interruption

to the incoming data stream is detected by the Reclocker,

the Carrier Detect goes LOW and opens the AFT loop in

order to maintain the correct VCO frequency for a period

of at least 2 seconds. This allows the Reclocker to rapidly

relock when the signal is re-established.

the potentiometer to determine the error free low limit of the

capture range. Error free operation is determined by using a

suitable CRC or EDH measurement method to obtain a stable

signal with no errors. Record the loop filter voltage at this point

as V . Now adjust the potentiometer so that the loop filter

CL

voltage is 250 mV above V .

CL

11 of 13

32467 - 0

Share Link: