EL7558BCM Просмотр технического описания (PDF) - Intersil

Номер в каталоге

Компоненты Описание

производитель

EL7558BCM

Integrated Adjustable 8 Amp Synchronous Switcher

Intersil 

EL7558B

Applications Information

Circuit Description

General

The EL7558B is a fixed frequency, current mode controlled

DC:DC converter with integrated N-channel power

MOSFETS and a high precision reference. The device

incorporates all of the active circuitry required to implement

a cost effective, user-programmable 8A synchronous buck

converter suitable for use in CPU power supplies. By

combining HSOP packaging technology with an efficient

synchronous switching architecture, high power outputs

(30W) can be realized without the use of externally attached

heat sinks.

Theory of Operation

The EL7558B is composed of 7 major blocks:

1. PWM Controller

2. Output Voltage Mode Select

3. NMOS Power FETS and Drive Circuitry

4. Bandgap Reference

5. Oscillator

6. Temperature Sensor

7. Power Good and Power On Reset

PWM Controller

The EL7558B regulates output voltage through the use of

current-mode controlled pulse width modulation. The three

main elements in a PWM controller are the feedback loop

and reference, a pulse width modulator whose duty cycle is

controlled by the feedback error signal, and a filter which

averages the logic level modulator output. In a step-down

(buck) converter, the feedback loop forces the time-averaged

output of the modulator to equal the desired output voltage.

Unlike pure voltage-mode control systems current-mode

control utilizes dual feedback loops to provide both output

voltage and inductor current information to the controller.

The voltage loop minimizes DC and transient errors in the

output voltage by adjusting the PWM duty-cycle in response

to changes in line or load conditions. Since the output

voltage is equal to the time-average of the modulator output

the relatively large LC time constants found in power supply

applications generally results in low bandwidth and poor

transient response. By directly monitoring changes in

inductor current via a series sense resistor the controller’s

response time is not entirely limited by the output LC filter

and can react more quickly to changes in line or load

conditions. This feed-forward characteristic also simplifies

AC loop compensation since it adds a zero to the overall

loop response. Through proper selection of the current-

feedback to voltage-feedback ratio, the overall loop response

will approach a one pole system. The resulting system offers

several advantages over traditional voltage control systems,

including simpler loop compensation, pulse by pulse current

limiting, rapid response to line variation and good load step

response.

The heart of the controller is a triple-input direct summing

comparator which sums voltage feedback, current feedback

and slope compensating ramp signals together. Slope

compensation is required to prevent system instability which

occurs in current-mode topologies operating at duty-cycles

greater than 50% and is also used to define the open-loop

gain of the overall system. The compensation ramp

amplitude is user adjustable and is set using a single

external capacitor (CSLOPE). Each comparator input is

weighted and determines the load and line regulation

characteristics of the system. Current feedback is measured

by sensing the inductor current flowing through the high-side

switch whenever it is conducting. At the beginning of each

oscillator period the high-side NMOS switch is turned on and

CSLOPE ramps positively from its reset state (VREF

potential). The comparator inputs are gated off for a

minimum period of time (LEB) after the high-side switch is

turned on to allow the system to settle. The Leading Edge

Blanking (LEB) period prevents the detection of erroneous

voltages at the comparator inputs due to switching noise.

When programming low regulator output voltages the LEB

delay will limit the maximum operating frequency of the

circuit since the LEB will result in a minimum duty-cycle

regardless of the PWM error voltage. This relationship is

shown in the performance curves. If the inductor current

exceeds the maximum current limit (ILMAX), a secondary

over-current comparator will terminate the high-side switch.

If ILMAX has not been reached, the regulator output voltage

is then compared to the reference voltage VREF. The

resultant error voltage is summed with the current feedback

and slope compensation ramp. The high-side switch remains

on until all three comparator inputs have summed to zero, at

which time the high-side switch is turned off and the low-side

switch is turned on. In order to eliminate cross-conduction of

the high-side and low-side switches a 10ns break-before-

make delay is incorporated in the switch driver circuitry. In

the continuous mode of operation the low-side switch will

remain on until the end of the oscillator period. In order to

improve the low current efficiency of the EL7558B, a zero-

crossing comparator senses when the inductor transitions

through zero. Turning off the low-side switch at zero inductor

current prevents forward conduction through the internal

clamping diodes (LX to VSSP) when the low-side switch

turns off, reducing power dissipation. The output enable

(OUTEN) input allows the regulator output to be disabled by

an external logic control signal.

Output Voltage Mode Select

The VCC2DET multiplexes the FB1 and FB2 pins to the

PWM controller. A logic 1 on VCC2DET selects the FB2

input and forces the output voltage to the internally

programmed value of 3.50V. A logic zero on VCC2DET

9

Share Link: