EL5420T Просмотр технического описания (PDF) - Intersil
Номер в каталоге
Компоненты Описание
производитель
EL5420T Datasheet PDF : 17 Pages
| |||
EL5420T
Electrical Specifications VS+ = +18V, VS- = 0V, RL = 10kΩ to 9V, TA = +25°C, unless otherwise specified.
PARAMETER
DESCRIPTION
CONDITIONS
MIN TYP
MAX
UNIT
INPUT CHARACTERISTICS
VOS
TCVOS
Input Offset Voltage
Average Offset Voltage Drift (Note 4)
VCM = 9V
14 LD TSSOP, SOIC package
16 LD QFN package
4
15
mV
7
µV/°C
2
µV/°C
IB
RIN
CIN
CMIR
Input Bias Current
Input Impedance
Input Capacitance
Common-Mode Input Range
VCM = 9V
2
50
nA
1
GΩ
2
pF
-0.5
+18.5
V
CMRR
Common-Mode Rejection Ratio
AVOL
Open Loop Gain
OUTPUT CHARACTERISTICS
For VINx from -0.5V to +18.5V
0.5V ≤ VOUTx ≤ 17.5V
53
78
dB
75
90
dB
VOL
VOH
ISC
Output Swing Low
Output Swing High
Short Circuit Current
IOUT
Output Current
POWER SUPPLY PERFORMANCE
IL = -9mA
IL = +9mA
VCM = 9V, Source: VOUTx short to VS-,
Sink: VOUTx short to VS+
100
150
mV
17.85 17.90
V
±200
mA
±70
mA
(VS+) - (VS-)
IS
PSRR
Supply Voltage Range
Supply Current (Per Amplifier)
Power Supply Rejection Ratio
VCM = 9V, No load
Supply is moved from 4.5V to 19V
4.5
19
V
550
750
µA
60
75
dB
DYNAMIC PERFORMANCE
SR
tS
BW
GBWP
PM
CS
Slew Rate (Note 5)
Settling to +0.1% (Note 6)
-3dB Bandwidth
Gain-Bandwidth Product
Phase Margin
Channel Separation
1V ≤ VOUTx ≤ 17V, 20% to 80%
AV = +1, VOUTx = 2V step,
RL= 10kΩ, CL= 8pF
RL= 10kΩ, CL= 8pF
AV = -50, RF = 5kΩ, RG= 100Ω
RL= 10kΩ, CL= 8pF
AV = -50, RF = 5kΩ, RG= 100Ω
RL= 10kΩ, CL= 8pF
f = 5MHz
12
V/µs
500
ns
12
MHz
8
MHz
50
°
75
dB
NOTES:
4. Measured over -40°C to +85°C ambient operating temperature range. See the typical TCVOS production distribution shown in the
“Typical Performance Curves” on page 6
5. Typical slew rate is an average of the slew rates measured on the rising (20%-80%) and the falling (80%-20%) edges of the output signal.
6. Settling time measured as the time from when the output level crosses the final value on rising/falling edge to when the output level settles within
a ±0.1% error band. The range of the error band is determined by: Final Value(V)±[Full Scale(V)*0.1%]
5
FN6838.0
September 25, 2009
Share Link: 