DS2156 Просмотр технического описания (PDF) - Maxim Integrated

Номер в каталоге

Компоненты Описание

производитель

DS2156

T1/E1/J1 Single-Chip Transceiver TDM/UTOPIA II Interface

Maxim Integrated 

DS2156

1. MAIN FEATURES

The DS2156 contains all of the features of the previous generation of Dallas Semiconductor’s T1 and E1 SCTs plus

many new features such as a UTOPIA bus interface.

General

Programmable output clocks for fractional T1, E1,

H0, and H12 applications

Interleaving PCM bus operation

8-bit parallel control port, multiplexed or

nonmultiplexed, Intel or Motorola

IEEE 1149.1 JTAG-Boundary Scan

3.3V supply with 5V tolerant inputs and outputs

Pin compatible with DS2155, DS2152/DS2154,

and DS21x5Y SCT family

Signaling System 7 Support

RAI-CI, AIS-CI support

100-pin LQFP package (14mm x 14mm) (DS2156)

3.3V supply with 5V tolerant inputs and outputs

LQFP package that is pin compatible with

DS2152/DS2154, DS21352/DS21354,

DS21552/DS21554, and DS2155

Evaluation kits

IEEE 1149.1 JTAG boundary scan

Driver source code available from the factory

Line Interface

Requires only a 2.048MHz master clock for both

E1 and T1 operation with the option to use

1.544MHz for T1 operation

Fully software configurable

Short-haul and long-haul applications

Automatic receive sensitivity adjustments

Ranges include 0 to 43dB or 0 to 12dB for E1

applications and 0 to 13dB or 0 to 36dB for T1

applications

Receive level indication in 2.5dB steps from

-42.5dB to -2.5dB

Internal receive termination option for 75Ω, 100Ω,

and 120Ω lines

Internal transmit termination option for 75Ω, 100Ω,

and 120Ω lines

Monitor application gain settings of 20dB, 26dB,

and 32dB

G.703 receive synchronization-signal mode

Flexible transmit waveform generation

T1 DSX-1 line buildouts

T1 CSU line buildouts of -7.5dB, -15dB, and

-22.5dB

E1 waveforms include G.703 waveshapes for

both 75Ω coax and 120Ω twisted cables

AIS generation independent of loopbacks

Alternating ones and zeros generation

Square-wave output

Open-drain output option

NRZ format option

Transmitter power-down

Transmitter 50mA short-circuit limiter with

current-limit-exceeded indication

Transmit open-circuit-detected indication

Line interface function can be completely

decoupled from the framer/formatter

Clock Synthesizer

Output frequencies include 2.048MHz, 4.096MHz,

8.192MHz, and 16.384MHz

Derived from recovered receive clock

Jitter Attenuator

32-bit or 128-bit crystal-less jitter attenuator

Requires only a 2.048MHz master clock for both

E1 and T1 operation with the option to use

1.544MHz for T1 operation

Can be placed in either the receive or transmit path

or disabled

Limit trip indication

Framer/Formatter

Fully independent transmit and receive

functionality

Full receive and transmit path transparency

T1 framing formats include D4 (SLC-96) and ESF

Detailed alarm and status reporting with optional

interrupt support

Large path and line error counters for:

– T1: BPV, CV, CRC6, and framing bit errors

– E1: BPV, CV, CRC4, E-bit, and frame

alignment errors

Timed or manual update modes

DS1 idle code generation on a per-channel basis in

both transmit and receive paths

– User-defined

– Digital milliwatt

ANSI T1.403-1998 Support

RAI-CI detection and generation

AIS-CI detection and generation

E1ETS 300 011 RAI generation

G.965 V5.2 link detect

Ability to monitor one DS0 channel in both the

transmit and receive paths

In-band repeating pattern generators and detectors

– Three independent generators and detectors

– Patterns from 1 to 8 bits or 16 bits in length

9 of 265

Share Link: