CRCW0805-HP Просмотр технического описания (PDF) - Vishay Semiconductors
Номер в каталоге
Компоненты Описание
производитель
CRCW0805-HP Datasheet PDF : 10 Pages
| |||
www.vishay.com
CRCW-HP e3
Vishay Draloric
TEST PROCEDURES AND REQUIREMENTS
IEC
EN 60115-1 60068-2 (1)
CLAUSE
TEST
METHOD
TEST
PROCEDURE
REQUIREMENTS
PERMISSIBLE CHANGE (R)
Stability for product types:
STABILITY CLASS 2 OR BETTER
CRCW-HP e3
1 to 1 M
4.19
4.13
14 (Na)
-
Rapid change of
temperature
Short time overload
30 min at -55 °C and
30 min at 125 °C;
1000 cycles
U = 2.5 x P70 x R 2 x Umax.;
whichever is the less severe;
5s
± (1 % R + 0.05 )
no visible damage
± (2 % R + 0.05 )
Severity no. 4:
4.27
-
Single pulse high
voltage overload
U = 10 x P70 x R or
U = 2 x Umax.;
whichever is the less severe;
10 pulses 10 μs/700 μs
± (1 % R + 0.05 )
no visible damage
U = 15 x P70 x R or
4.39
-
Periodic electric
overload
U = 2 x Umax.;
whichever is the less severe;
0.1 s on; 2.5 s off;
1000 cycles
± (1 % R + 0.05 )
no visible damage
Electrostatic
IEC 61340-3-1 (1);
4.38
-
discharge
3 pos. + 3 neg. discharges;
(human body model) ESD voltage acc. to the size
± (1 % R + 0.05 )
Endurance by sweeping;
10 Hz to 2000 Hz;
4.22
6 (Fc)
Vibration
no resonance;
amplitude 1.5 mm or
200 m/s2;
7.5 h
± (0.5 % R + 0.05 )
no visible damage
Solder bath method;
Sn60Pb40
non-activated flux;
(235 ± 5) °C;
(2 ± 0.2) s
4.17
58 (Td)
Solderability
Solder bath method;
Sn96.5Ag3Cu0.5
non-activated flux;
(245 ± 5) °C;
(3 ± 0.3) s
Good tinning ( 95 % covered)
no visible damage
Solder bath method
4.18
58 (Td)
Resistance to
soldering heat
(260 ± 5) °C;
(10 ± 1) s
± (0.5 % R + 0.05 )
4.29
45 (XA)
Component solvent
resistance
Isopropyl alcohol;
+50 °C; method 2
No visible damage
4.32
21 (Uu3)
Shear
(adhesion)
CRCW0402-HP and
CRCW0603-HP: 9 N
CRCW0805-HP to
CRCW2512-HP: 45 N
No visible damage
4.33
21 (Uu1) Substrate bending
Depth 2 mm;
3 times
± (0.25 % R + 0.05 )
no visible damage, no open circuit in bent position
4.7
-
Voltage proof
U = 1.4 x Uins; 60 s
4.35
-
Flammability,
needle flame test
IEC 60695-11-5 (1);
10 s
No flashover or breakdown
No burning after 30 s
Note
(1) The quoted IEC standards are also released as EN standards with the same number and identical contents
Revision: 27-Oct-2020
8
Document Number: 20043
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Share Link: 