AM79C981JC Просмотр технического описания (PDF) - Advanced Micro Devices

Номер в каталоге

Компоненты Описание

производитель

AM79C981JC

Integrated Multiport Repeater Plus™ (IMR+™)

Advanced Micro Devices 

PRELIMINARY

PIN DESCRIPTION

ACK

Acknowledge

Input, Active LOW

When this input is asserted, it signals to the requesting

IMR+ device that it may control the DAT and JAM pins.

If the IMR+ chip is not requesting control of the DAT line

(REQ pin HIGH), then the assertion of the ACK signal

indicates the presence of valid collision status on the

JAM or valid data on the DAT line.

AVDD

Analog Power

Power Pin

These pins supply the +5 V to the RXD+/– receivers,

the DI+/– and CI+/– receivers, the DO+/– drivers, the

internal PLL, and the internal voltage reference of the

IMR+ device. These power pins should be decoupled

and kept separate from other power and ground

planes.

AVSS

Analog Ground

Ground Pin

These pins are the 0 V reference for AVDD.

COL

Expansion Collision

Input, Active LOW

When this input is asserted by an external arbiter, it sig-

nifies that more than one IMR+ device is active and that

each IMR+ device should generate the Collision Jam

sequence independently.

CI+, CI–

Control In

Input

AUI port differential receiver. Signals comply with IEEE

802.3, Section 7.

CRS

Carrier Sense

Output

The states of the internal carrier sense signals for the

AUI port and the eight twisted-pair ports are serially

output on this pin continuously. The output serial bit

stream is synchronized to the X1 clock.

DAT

Data

Input/Output/3-State

In non-collision conditions, the active IMR+ device will

drive DAT with NRZ data, including regenerated pre-

amble. During collision, when JAM = HIGH, DAT is

used to signal a multiport (DAT = 0) or single-port

(DAT = 1) condition.

When ACK is not asserted, DAT is in high impedance.

If REQ and ACK are both asserted, then DAT is an out-

put. If ACK is asserted and REQ not asserted, then

DAT is an input.

This pin needs to be either pulled up or pulled down

through a high-value resistor.

DI+, DI–

Data In

Input

AUI port differential receiver. Signals comply with IEEE

802.3, Section 7.

DO+, DO–

Data Out

Output

AUI port differential driver. Signals comply with IEEE

802.3, Section 7.

DVDD

Digital Power

Power Pin

These pins supply +5 V to the logic portions of the

IMR+ chip and the TXP+/–, TXD+/–, and DO+/– line

drivers.

DVSS

Digital Ground

Ground Pin

These pins are the 0 V reference for DVDD.

DVDD Pin #

19

DVSS Pin #

Function

16

TP ports 0 & 1 drivers

28

31

TP ports 2 & 3 drivers

43, 49

35, 37, 46, 51

Core logic and expansion

and control pins

59

56

TP ports 4 & 5 drivers

68

71

TP ports 6 & 7 drivers

JAM

Jam

Input/Output/3-State

When JAM is asserted, the state of DAT will indicate

either a multiport (DAT = 0) or single-port (DAT = 1) col-

lision condition.

When ACK is not asserted, JAM is in high impedance.

If REQ and ACK are both asserted, then JAM is an out-

put. If ACK is asserted and REQ not asserted, then

JAM is an input.

This pin needs to be either pulled up or pulled down

through a high-value resistor.

1–76

Am79C981

Share Link: