ALD1123E(2003) Просмотр технического описания (PDF) - Advanced Linear Devices
Номер в каталоге
Компоненты Описание
производитель
ALD1123E
(Rev.:2003)
(Rev.:2003)
Advanced Linear Devices
ALD1123E Datasheet PDF : 8 Pages
| |||
ABSOLUTE MAXIMUM RATINGS
Supply voltage, V+ referenced to V-
Supply voltage, VS referenced to V-
Differential input voltage range
Power dissipation
Operating temperature range PA, SA, PC, SC package
DA, DC package
Storage temperature range
Lead temperature, 10 seconds
OPERATING ELECTRICAL CHARACTERISTICS
TA = 25°C V+ = +5.0V unless otherwise specified
Parameter
ALD1123E
Symbol Min Typ
Max
ALD1121E
Min
Typ
Max
Drain to Source Voltage 1
VDS
10.0
10.0
Initial Threshold Voltage 2
Vt i
0.990 1.000 1.010 0.990 1.000 1.010
Unit
V
V
E-trim Vt Range
Drain - Gate Connected
Voltage Tempco
Vt
1.000
TCVDS
-1.6
-0.3
0.0
+2.7
3.000 1.000
3.000
-1.6
-0.3
0.0
+2.7
V
mV/°C
mV/°C
mV/°C
mV/°C
Initial Offset Voltage 3
VOS i
1
5
1
5 mV
-0.3V to +13.2V
±6.6V
0.3V to V+ +0.3V
600 mW
0°C to +70°C
-55°C to +125°C
-65°C to +150°C
+260°C
Test
Conditions
IDS = 1µA TA = 21°C
ID = 5µA
ID = 50µA
ID = 68µA
ID = 500µA
Tempco of VOS
TCVOS
Differential Threshold Voltage 4 DV t
Tempco of Differential
Threshold Voltage 4
TCDV t
Long Term Drift
∆Vt /∆t
Long Term Drift Match
∆Vt /∆t
Drain Source On Current
IDS(ON)
Drain Source On Current 4
IDS(ON)
Initial Zero Tempco Voltage 3
Zero Tempco Current
VZT C i
IZTC
Initial On-Resistance 3
On-Resistance Match
RON i
∆RON
5
2.000
0.033
-0.02
-5
3.0
-0.05
0.8
1.52
68
500
0.5
5
µV/°C
2.000 V
VDS1 = VDS2
0.033
mV/°C
-0.02 -0.05 mV
-5
µV
3.0
mA
0.8
mA
1.52
V
68
µA
500
Ω
0.5
%
1000 Hours
1000 Hours
VG =VD = 5V VS = 0V
Vt = 1.0
VG =VD = 5V VS = 0V
Vt = 3.0
Vt = 1.000V
VGS ¡= 5V VDS = 0.1V
NOTES:
1. V+ must be the most positive supply rail and V- must be at the most negative supply rail. Source terminals other than those labeled as V- can be at
any voltage between V- and V+.
2. Initial Threshold Voltage is set at the factory. If no EPAD Vt trimming is intended by user, then this is also the final or permanent threshold voltage
value.
3. Initial and Final values are the same unless deliberately changed by user.
4. These parameters apply only when Vt of one or more of the devices are to be changed by user.
ALD1123E/ALD1121E
Advanced Linear Devices
3
Share Link: