ASAHI KASEI
[AK2570]
Register map
Data
Name Address
D23 ~ D8 D7 D6 D5 D4 D3 D2 D1 D0
Function
RTMP 000 X ~ X D7 D6 D5 D4 D3 D2 D1 D0 Holding the data (temperature) generated by AD2
RDA1 001 X ~ X D7 D6 D5 D4 D3 D2 D1 D0
Holding the data for DA1
RDA2 010 X ~ X D7 D6 D5 D4 D3 D2 D1 D0
Holding the data for DA2
RDA3 011 X ~ X D7 D6 D5 D4 D3 D2 D1 D0
Holding the data for DA3
RINT 100 X ~ X X X X D4 D3 D2 D1 D0 Holding the trimming data for T-SENSE [*1]
RVPD 101 X ~ X D7 D6 D5 D4 D3 D2 D1 D0 Holding the data (VPDIN) generated by AD1
RATRM 110 X ~ X X X X D4 D3 D2 D1 D0 Holding the trimming data for ALMOUT [*2]
[*1] RINT register stores the initial data for the offset voltage of the T-SENSE
[*2] ATRM register stores the adjustment data for the alarm timing at the 50Mbps and the 156Mbps burst trans-
mission (AKM recommends to use the EEPROM data for RATRM register already written at the shipment.)
Initial register data
Name Address D23 ~
RTMP
000
X~
RDA1
001
X~
RDA2
010
X~
RDA3
011
X~
RINT
100
X~
D8 D7 D6 D5 D4 D3 D2 D1 D0
X1 1 1 1 1 1 1 1
X0 0 0 0 0 0 0 0
X0 0 0 0 0 0 0 0
X0 0 0 0 0 0 0 0
XXX X 0 0 0 0 0
RVPD
101
X ~ X0 0 0 0 0 0 0 0
RATRM
110
X ~ XXX X 1 0 0 0 0
<Note> ‘X’ is indefinite, ‘1’ or ‘0’.
IV) EEPROM Access
[1] Command for enabling to write the data in the EEPROM (EWEN)
‘EWEN’ command makes it possible to write the data in the EEPROM. It is necessary to execute this
command before writing the data in the EEPROM, because it is automatically set at ‘Power ON’ to prohibit
writing the data in the EEPROM. In “Training mode”, it is always possible to write the data in the EEPROM
after executing this command except the case of ‘Power OFF’ or executing ‘EWDS’ command.
[2] Command for prohibiting to write the data in the EEPROM (EWDS)
‘EWDS’ command makes it impossible to write the data in the EEPROM and it is the same setting at
‘Power ON’. This command is available to change the setting to prohibit writing the data in the EEPROM
without ‘Power OFF’.
[3] Command for writing the data in the EEPROM (WRITE-EEP)
It is able to write the data in the nominated EEPROM by executing ‘WRITE-EEP’ command. And it is
necessary to execute ‘EWEN’ command at first for permitting to write the data in the EEPROM.
[4] Command for reading the data in the EEPROM (READ-EEP)
It is able to read the data held in the nominated EEPROM by executing ‘READ-EEP’ command.
<MS0115-E-00>
9
2001/10