ADSP-2184L(Rev0) Просмотр технического описания (PDF) - Analog Devices

Номер в каталоге

Компоненты Описание

производитель

ADSP-2184L
(Rev.:Rev0)

DSP Microcomputer

Analog Devices 

ADSP-2184L

When PMOVLAY is set to 1 or 2, external accesses occur at

addresses 0x2000 through 0x3FFF. The external address is

generated as shown in Table II.

Table II.

PMOVLAY Memory A13

A12:0

0

Internal Not Applicable Not Applicable

1

External

Overlay 1 0

13 LSBs of Address

Between 0x2000

and 0x3FFF

2

External

Overlay 2 1

13 LSBs of Address

Between 0x2000

and 0x3FFF

NOTE: Addresses 0x2000 through 0x3FFF should not be accessed when

PMOVLAY = 0.

This organization provides for two external 8K overlay segments

using only the normal 14 address bits, which allows for simple

program overlays using one of the two external segments in

place of the on-chip memory. Care must be taken in using this

overlay space in that the processor core (i.e., the sequencer)

does not take into account the PMOVLAY register value. For

example, if a loop operation is occurring on one of the external

overlays and the program changes to another external overlay or

internal memory, an incorrect loop operation could occur. In

addition, care must be taken in interrupt service routines as the

overlay registers are not automatically saved and restored on the

processor mode stack.

When Mode B = 1, booting is disabled and overlay memory is

disabled. Figure 5 shows the memory map in this configuration.

The 4K internal pin cannot be accessed with Mode B = 1.

PROGRAM MEMORY

RESERVED

ADDRESS

0x3FFF

8K EXTERNAL

0x2000

0x1FFF

0x0000

Figure 5. Program Memory (Mode B = 1)

Data Memory

The ADSP-2184L has 4K 16-bit words of internal data memory.

In addition, the ADSP-2184L allows the use of 8K external

memory overlays. Figure 6 shows the organization of the data

memory.

DATA MEMORY

32 MEMORY–

MAPPED REGISTERS

4064 RESERVED WORDS

INTERNAL

4K

ADDRESS

0x3FFF

0x3FEO

0x3FDF

0x3000

0x2FFF

0x2000

0x1FFF

EXTERNAL 8K

(DMOVLAY = 1, 2)

0x0000

Figure 6. Data Memory

There are 4K words of memory accessible internally when the

DMOVLAY register is set to 0. When DMOVLAY is set to 1 or

2, external accesses occur at addresses 0x0000 through 0x1FFF.

The external address is generated as shown in Table III.

Table III.

DMOVLAY Memory A13

A12:0

0

Internal Not Applicable Not Applicable

1

External

Overlay 1 0

13 LSBs of Address

Between 0x0000

and 0x1FFF

2

External

Overlay 2 1

13 LSBs of Address

Between 0x0000

and 0x1FFF

This organization allows for two external 8K overlays using only

the normal 14 address bits. All internal accesses complete in one

cycle. Accesses to external memory are timed using the wait

states specified by the DWAIT register.

I/O Space (Full Memory Mode)

The ADSP-2184L supports an additional external memory

space called I/O space. This space is designed to support simple

connections to peripherals or to bus interface ASIC data regis-

ters. I/O space supports 2048 locations. The lower eleven bits

of the external address bus are used; the upper three bits are

undefined. Two instructions were added to the core ADSP-

2100 Family instruction set to read from and write to I/O

memory space. The I/O space also has four dedicated three-bit

wait state registers, IOWAIT0-3, that specify up to seven wait

states to be automatically generated for each of four regions.

The wait states act on address ranges as shown in Table IV.

Table IV.

Address Range

0x000–0x1FF

0x200–0x3FF

0x400–0x5FF

0x600–0x7FF

Wait State Register

IOWAIT0

IOWAIT1

IOWAIT2

IOWAIT3

–8–

REV. 0

Share Link: