A1244 Просмотр технического описания (PDF) - Allegro MicroSystems

Номер в каталоге

Компоненты Описание

производитель

A1244

Chopper-Stabilized, Two Wire Hall Effect Latch

Allegro MicroSystems 

A1244

Chopper-Stabilized, Two Wire

Hall-Effect Latch

Power Derating

The device must be operated below the maximum junction tem-

perature of the device, TJ(max). Under certain combinations of

peak conditions, reliable operation may require derating supplied

power or improving the heat dissipation properties of the appli-

cation. This section presents a procedure for correlating factors

affecting operating TJ. (Thermal data is also available on the

Allegro MicroSystems Web site.)

The Package Thermal Resistance, RJA, is a figure of merit sum-

marizing the ability of the application and the device to dissipate

heat from the junction (die), through all paths to the ambient air.

Its primary component is the Effective Thermal Conductivity, K,

of the printed circuit board, including adjacent devices and traces.

Radiation from the die through the device case, RJC, is relatively

small component of RJA. Ambient air temperature, TA, and air

motion are significant external factors, damped by overmolding.

The effect of varying power levels (Power Dissipation, PD), can

be estimated. The following formulas represent the fundamental

relationships used to estimate TJ, at PD.

× PD = VIN IIN

(1)

 T = PD × RJA

(2)

TJ = TA + ΔT

(3)

For example, given common conditions such as: TA= 25°C,

VCC = 12 V, ICC = 4 mA, and RJA = 140 °C/W, then:

Example: Reliability for VCC at TA=150°C, package LH, using a

low-K PCB.

Observe the worst-case ratings for the device, specifically:

RJA=110 °C/W, TJ(max) =165°C, VCC(max)= 24 V, and

ICC(max) = 17 mA.

Calculate the maximum allowable power level, PD(max). First,

invert equation 3:

Tmax = TJ(max) – TA = 165 °C – 150 °C = 15 °C

This provides the allowable increase to TJ resulting from internal

power dissipation. Then, invert equation 2:

PD(max) = Tmax ÷ RJA = 15°C ÷ 110 °C/W = 136 mW

Finally, invert equation 1 with respect to voltage:

VCC(est) = PD(max) ÷ ICC(max) = 136 mW ÷ 17 mA = 8 V

The result indicates that, at TA, the application and device can

dissipate adequate amounts of heat at voltages ≤VCC(est).

Compare VCC(est) to VCC(max). If VCC(est) ≤ VCC(max), then reli-

able operation between VCC(est) and VCC(max) requires enhanced

RJA. If VCC(est) ≥ VCC(max), then operation between VCC(est)

and VCC(max) is reliable under these conditions.

PD = VCC × ICC = 12 V × 4 mA = 48 mW



T = PD × RJA = 48 mW × 140 °C/W = 7°C

TJ = TA + T = 25°C + 7°C = 32°C

A worst-case estimate, PD(max), represents the maximum allow-

able power level (VCC(max), ICC(max)), without exceeding

TJ(max), at a selected RJA and TA.

Allegro MicroSystems, LLC

9

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Share Link: