499D686X06R3D1AE3 Просмотр технического описания (PDF) - Vishay Semiconductors
Номер в каталоге
Компоненты Описание
производитель
499D686X06R3D1AE3 Datasheet PDF : 9 Pages
| |||
www.vishay.com
489D, 499D
Vishay Sprague
PERFORMANCE CHARACTERISTICS
1. Operating Temperature: -55 °C to +85 °C with rated DC
voltage UR applied. +85 °C to +125° C with linear voltage
derating to category voltage UC for 499D only (see
general information)
2. Capacitance and Tolerance: capacitance measured at
100 Hz and +25 °C shall be within the specified tolerance
limits of the nominal rating. Capacitance measurement
shall be made by means of a polarized capacitance
bridge. No polarizing voltage is required. The maximum
voltage applied during measurements shall be 0.5 VRMS
at 100 Hz and +25 °C.
3. Reverse Voltage: these capacitors are capable of
withstanding peak voltage in the reverse direction equal to:
15 % of the rated DC voltage at +20 °C
10 % of the rated DC voltage at +25 °C
5 % of the rated DC voltage at +85 °C
4. Surge Voltage:
DC rated voltage
at +85 °C (V)
3 6.3 10 16 20 25 35 50
DC surge voltage
at +85 °C (V)
4
8 13 20 26 32 46 65
DC rated voltage
at +125 °C (V) (1)
2
4
7 10 13 17 23 33
DC surge voltage
at +125 °C (V) (1)
2.6 5.2 8.6 13
16
21
28
40
Note
(1) For 499D
Capacitors shall withstand the surge voltage applied in
series with a 1000 (± 5 %) resistor, at the rate of 1.5 min
on, 5.5 min off for 1000 successive test cycles at +85 °C.
5. Stability at low and high temperatures:
489D - Table 2A
After test, capacitance change shall not exceed 10 % of
initial value, dissipation factor and DC leakage current
shall meet initial requirements at +25 °C - Table 2.
6. Life Test: after 2000 h at +85 °C with rated DC voltage
applied, or after 1000 h at +125 °C. With derated DC
voltage (only for 499D), capacitors shall meet the
requirements in table below.
Capacitance change
DC leakage current
Dissipation factor
Within ± 10 % of initial value
Within initial requirements at +25 °C
Within initial requirements at +25 °C
7. Humidity Test: after 21 days (504 h) (1) at +40 °C, 90 %
to 95 % of relative humidity (per IEC 68-2-3) with no
voltage applied, capacitors shall meet the requirements
in table below.
Capacitance change
DC leakage current
Dissipation factor
Within ± 5 % of initial value
Within initial requirements
at +25 °C - Table 2
Within initial requirements
at +25 °C - Table 2
Note
(1) Humidity test is 56 days (1350 hours) for 499D
8. Marking: the capacitors shall be marked with the rated
capacitance and the rated DC working voltage. A code
may be used for both capacitance and voltage. Units
rated at 6.3 volts are usually marked as 6 volts. The
package shall be marked with full Vishay part number,
date code, and quantity.
TEMP.
-55 °C
+25 °C
+85 °C
CAPACITANCE CHANGE
-10 % of initial value
-------------
+10 % of initial value
DC LEAKAGE CURRENT (1)
-----------
0.015 CR x UR or 1 μA,
whichever is greater
0.15 CR x UR or 10 μA,
whichever is greater
DISSIPATION FACTOR AT 100 Hz
CR 1.5 μF
1.5 μF < CR < 10 μF
10 μF < CR < 100 μF
100 μF CR 330 μF
330 μF < CR
4 % max
6 % max
8 % max
10 % max
12 % max
TEMP.
CAPACITANCE CHANGE DC LEAKAGE CURRENT (1)
-55 °C
-10 % of initial value
-------------
+25 °C
------------
0.008 CR x UR or 0.5 μA,
whichever is greater
+85 °C
+10 % of initial value
0.08 CR x UR or 5 μA,
whichever is greater
+125 °C (2)
+10 % of initial value
0.1 CR x UR or 6.25 μA,
whichever is greater
Notes
(1) Rated voltage applied for 5 min with a series resistor of 1000
(2) Only for 499 D
DISSIPATION FACTOR AT 100 Hz
CR 1.5 μF
1.5 μF < CR < 10 μF
10 μF < CR < 100 μF
100 μF CR 330 μF
330 μF < CR
4 % max
6 % max
8 % max
10 % max
12 % max
Revision: 21-Feb-18
6
Document Number: 42070
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Share Link: 