24LC320 Просмотр технического описания (PDF) - Microchip Technology

Номер в каталоге

Компоненты Описание

производитель

24LC320

32K 2.5V SPI™ Bus Serial EEPROM

Microchip Technology 

25LC320

2.0 PRINCIPLES OF OPERATION

The 25LC320 is a 4096 byte EEPROM designed to

interface directly with the serial peripheral interface

(SPI™) port of many of today’s popular microcontroller

families, including Microchip’s midrange PIC16CXX

microcontrollers. It may also interface with microcontrol-

lers that do not have a built-in SPI™ port by using dis-

crete I/O lines programmed properly with software.

The 25LC320 contains an 8-bit instruction register. The

part is accessed via the SI pin, with data being clocked

in on the rising edge of SCK. If the WPEN bit in the Sta-

tus Register is set, the WP pin must be held high to

allow writing to the non-volatile bits in the status regis-

ter.

Table 2-1 contains a list of the possible instruction bytes

and format for device operation. All instructions,

addresses and data are transferred MSB first, LSB last.

Data is sampled on the first rising edge of SCK after CS

goes low. If the clock line is shared with other peripheral

devices on the SPI™ bus, the user can assert the

HOLD input and place the 25LC320 in ‘HOLD’ mode.

After releasing the HOLD pin, operation will resume

from the point when the HOLD was asserted.

2.1 Write Enable (WREN) and Write

Disable (WRDI)

The 25LC320 contains a write enable latch. This latch

must be set before any write operation will be

completed internally. The WREN instruction will set the

latch, and the WRDI will reset the latch. The following is

a list of conditions under which the write enable latch

will be reset:

• Power-up

• WRDI instruction successfully executed

• WRSR instruction successfully executed

• WRITE instruction successfully executed

2.2 Read Status Register (RDSR)

The RDSR instruction provides access to the status

register. The status register may be read at any time,

even during a write cycle. The status register is format-

ted as follows:

7 654 3

2

1

0

WPEN X X X BP1 BP0 WEL WIP

The Write-In-Process (WIP) bit indicates whether the

25LC320 is busy with a write operation. When set to a

‘1’ a write is in progress, when set to a ‘0’ no write is in

progress. This bit is read only.

The Write Enable Latch (WEL) bit indicates the status

of the write enable latch. When set to a ‘1’ the latch

allows writes to the array and status register, when set

to a ‘0’ the latch prohibits writes to the array and status

register. The state of this bit can always be updated via

the WREN or WRDI commands regardless of the state

of write protection on the status register. This bit is read

only.

The Block Protection (BP0 and BP1) bits indicate

which blocks are currently write protected. These bits

are set by the user issuing the WRSR instruction.

These bits are non-volatile.

The Write Protect Enable (WPEN) bit is a non-volatile

bit that is available as an enable bit for the WP pin. The

Write Protect (WP) pin and the Write Protect Enable

(WPEN) bit in the status register control the

programmable hardware write protect feature.

Hardware write protection is enabled when WP pin is

low and the WPEN bit is high. Hardware write

protection is disabled when either the WP pin is high or

the WPEN bit is low. When the chip is hardware write

protected, only writes to non-volatile bits in the status

register are disabled. See Table 2-2 for matrix of

functionality on the WPEN bit and Figure 2-1 for a

flowchart of Table 2-2. See Figure 3-5 for RDSR timing

sequence.

TABLE 2-1: INSTRUCTION SET

Instruction Name Instruction Format

Description

WREN

WRDI

RDSR

WRSR

READ

WRITE

0000 0110

0000 0100

0000 0101

0000 0001

0000 0011

0000 0010

Set the write enable latch (enable write operations)

Reset the write enable latch (disable write operations)

Read status register

Write status register (write protect enable and block write protection bits)

Read data from memory array beginning at selected address

Write data to memory array beginning at selected address

TABLE 2-2: WRITE PROTECT FUNCTIONALITY MATRIX

WPEN

0

0

1

1

X

X

WP

X

X

Low

Low

High

High

WEL

0

1

0

1

0

1

Protected Blocks

Protected

Protected

Protected

Protected

Protected

Protected

Unprotected Blocks

Protected

Writable

Protected

Writable

Protected

Writable

Status Register

Protected

Writable

Protected

Protected

Protected

Writable

© 1996 Microchip Technology Inc.

Preliminary

DS21158B-page 5

Share Link: