HIP0045 Просмотр технического описания (PDF) - Intersil

Номер в каталоге

Компоненты Описание

производитель

HIP0045

1A/50V Octal Low Side Power Driver With Serial Bus Control and Fault Protection

Intersil 

HIP0045

Detecting Fault Conditions

Fault conditions may be checked as follows: SCK is always

low when CE is changing. When CE goes low, the MISO

output is taken out of the three-state mode and the Output

status information is latched into the shift register. While CE is

low, data bits in the shift register are transferred to the MISO

output on each positive SCK clock transition and data bits

present at the MOSI input are transferred into the shift register

on each negative transition of SCK. To verify Status and

Diagnostic conditions, clock in a new control byte and wait

approximately 150µs to allow the outputs to settle. Clock in

the same control byte and compare this to the data output at

the MISO pin. If there is a disparity, use Tables 5, 6 and 7 to

determine the fault or status condition. (Use Tables 1, 2, 3 and

4 to establish the ON/OFF conditions for each output).

Based on the needs of the application, a software sequence

should be programmed into the microcontroller to set the

corrective action of each fault condition.

TABLE 5. DIAGNOSTIC FAILURE REGISTER STRUCTURE

Diag1 Diag3 Diag5 Diag7 Diag0 Diag2 Diag4 Diag6

(D7O) (D6O) (D5O) (D4O) (D3O) (D2O) (D1O) (D0O)

MSB

LSB

NOTE:

10. The Diagnostic Failure Register bits Diag0 -7 have the same

order as the Control Register bits Q0 - 7 as defined in Table 4.

Data bits D0O - D7O give the MISO SPI serial output flow

sequence.

TABLE 6. DEFINITION OF Diag0, 1 FAULT BITS FOR OUT0,

1 IN PARALLEL-CONTROLLED MODE

OUTPUT VREF

FAULT

STATE STATUS BIT

FAULT

MODE

OFF

OFF

ON

ON

>VREF

<VREF

<VREF

>VREF

H

No Fault

L

Open Load or GND Short

H

No Fault

L

Short to VBATT

TABLE 7. DEFINITION OF Diag0-7 STATUS BITS FOR OUT0-7

OUTPUT VREF STATUS

STATE STATUS BIT

FAULT

MODE

OFF

OFF

ON

ON

>VREF

<VREF

<VREF

>VREF

H

No Fault

L

Open Load or GND Short

L

No Fault

H

Short to VBATT (Chan. 0-7);

or Over-Temperature Fault

(Chan. 6, 7)

NOTES:

11. For Channel 0 (Diag0) and Channel 1 (Diag1):

Fault Bit High = No Fault; Fault Bit Low = Fault Occurred.

12. VREF is the threshold reference level for detecting an Open Load.

Refer to the Electrical Specification for the VREF voltage level.

Special Conditions for Channel 0, 1

Referring to the Detailed Block Diagram, Channel’s 0, 1 are

configured to externally provide control of the ON/OFF state.

The inputs, IN0 and IN1, are ORed with the SPI ON/OFF

control bit. In this configuration with IN0 and IN1 high, SPI

control latches Diag0 and Diag1 as status bits. When the IN0

and IN1 inputs are active, a fault condition is detected by a

comparison of IN0 and IN1 to OUT0 and OUT1 respectively

causing the Fault Detector to latch a fault bit. The resulting

Fault output is latched as diagnostic bit, Diag0 or Diag1. The

Diag0 and Diag1 outputs give the status or fault condition of

the output drivers as shown in Table 6. Fault detection is

disabled during switching/settling time.

The Diag0 and Diag1 bits from Channel 0 and 1 respectively

indicate a fault when the FAULT BIT is Low, given IN1 and

IN0 control. Otherwise Diag0 and Diag1 are status bits when

controlled by the SPI input. Note that the SPI Bit, given in

Tables 1 and 2 overrides the ON state control from IN0

and IN1.

1000

100

SAFE OPERATING AREA

BELOW LINE

10

0.1

1

10

100

TIME (ms)

FIGURE 4. MAXIMUM SINGLE PULSE ENERGY SAFE

OPERATING AREA FOR EACH CLAMPED

OUTPUT DRIVER, TA = 25oC

4-8

Share Link: