ADM1184 Просмотр технического описания (PDF) - Analog Devices
Номер в каталоге
Компоненты Описание
производитель
ADM1184 Datasheet PDF : 12 Pages
| |||
THEORY OF OPERATION
The ADM1184 is an integrated, 4-channel voltage-monitoring
device. A 2.7 V to 5.5 V power supply is required on the VCC pin
to power the device.
VCC = 2.7V TO 5.5V
3.3V
2.5V
VCC
1.8V
ADM1184
1.2V
VIN1
OUT1
VIN2
OUT2
VIN3
OUT3
ENABLE
SIGNALS
VIN4
GND
PWRGD
POWER
GOOD
Figure 16. Typical Applications Circuit
INPUT CONFIGURATION
Four precision comparators monitor four voltage rails.
Each comparator has a 0.6 V reference with a worst-case
accuracy of 0.8%. Resistor networks external to the VIN1,
VIN2, VIN3, and VIN4 pins set the trip points for the
monitored supply rails.
Typically, the threshold voltage at each of the four adjustable
inputs (that is, VIN1, VIN2, VIN3, and VIN4) is 0.6 V. To
monitor a voltage greater than 0.6 V, connect a resistor divider
network to the circuit as depicted in Figure 17.
V
3.3V
2.9V
0V
t
2.9V SUPPLY
GIVES 0.6V
AT VIN1 PIN
4.6kΩ
ADM1184
VIN1
1.2kΩ 0.6V
TO LOGIC
CORE
Figure 17. Setting the Undervoltage Threshold
In this example, the VIN1 pin monitors a 3.3 V supply. An
external resistor divider scales this voltage down for monitoring
at the VIN1 pin. The resistor ratio is chosen so that the VIN1
voltage is 0.6 V when the main voltage rises to the preferred level
at startup (a voltage below the nominal 3.3 V level). R1 is 4.6 kΩ
and R2 is 1.2 kΩ; therefore, a voltage level of 2.9 V corresponds
to 0.6 V on the noninverting input of the first comparator (see
Figure 17).
ADM1184
OUTPUT CONFIGURATION
The ADM1184 has four open-drain, active high outputs. Of
these outputs, OUT1 to OUT3 can be used to enable power
supplies, and PWRGD is a common power-good output.
Output OUT1 to Output OUT3 are dependent on their associated
input (that is, VIN1, VIN2, or VIN3). Before the voltage on a
VINx input reaches 0.6 V, the corresponding output is switched
to ground if there is 1 V on the VCC pin of the ADM1184. When
VINx detects 0.6 V, OUTx is asserted after a 30 μs (typical) delay.
When all four monitored supplies exceed 0.6 V, a system power-
good signal (PWRGD) is asserted. There is an internal 190 ms
(typical) delay associated with the assertion of the PWRGD
output. After PWRGD is asserted, if any of the four monitored
supplies drops below its programmed threshold, the corresponding
OUTx output and the PWRGD output are deasserted. If only
the supply monitored by VIN4 drops below its programmed
threshold, just the PWRGD output is deasserted.
The ADM1184 functional truth table is shown in Table 5. Note that
the functional operation described in Table 5 applies to the
operation both before and after the assertion of PWRGD.
Table 5. Functional Truth Table
VIN1 VIN2 VIN3 VIN4 OUT1
01
0
0
0
Low
0
0
0
12
Low
0
0
1
0
Low
0
0
1
1
Low
0
1
0
0
Low
0
1
0
1
Low
0
1
1
0
Low
0
1
1
1
Low
1
0
0
0
High
1
0
0
1
High
1
0
1
0
High
1
0
1
1
High
1
1
0
0
High
1
1
0
1
High
1
1
1
0
High
1
1
1
1
High
OUT2
Low
Low
Low
Low
High
High
High
High
Low
Low
Low
Low
High
High
High
High
OUT3
Low
Low
High
High
Low
Low
High
High
Low
Low
High
High
Low
Low
High
High
PWRGD
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
High
1 <VTH = 0.
2 >VTH = 1.
Figure 18 and Figure 19 show waveforms that illustrate the
behavior of the ADM1184.
Rev. 0 | Page 9 of 12
Share Link: 