59620252301QXA Просмотр технического описания (PDF) - Aeroflex UTMC

Номер в каталоге

Компоненты Описание

производитель

59620252301QXA

UT80C196KDS Microcontroller

Aeroflex UTMC 

1.1 Hardware Interface

1.1.1 Interfacing with External Memory

The UT80C196KDS can interface with a variety of external

memory devices. It supports either a fixed 8-bit bus width or a

dynamic 8-bit/16-bit bus width, internal READY control for

slow external memory devices, a bus-hold protocol that enables

external devices to take over the bus, and several bus-control

modes. These features provide a great deal of flexibility when

interfacing with external memory devices.

There are 8 configuration bits available in the CCR. However,

bits 7 and 6 are not used by the UT80C196KDS. Bits 5 and 4

comprise the READY mode control which define internal limits

for waitstates generated by the READY pin. Bit 3 controls the

definition of the ALE/ADV pin for system memory controls

while bit 2 selects between the different write modes. Bit 1

selects whether the UT80C196KDS will use a dynamic 16-bit

bus or whether it will be locked in as an 8-bit bus. Finally, Bit

0 enables the Power Down mode and allows the user to disable

this mode for protection against inadvertent power downs.

1.1.1.1 Chip Configuration Register

The Chip Configuration Register (CCR) is used to initialize the

UT80C196KDS immediately after reset. The CCR is fetched

from external address 2018H (Chip Configuration Byte) after

removal of the reset signal. The Chip Configuration Byte (CCB)

is read as either an 8-bit or 16-bit word depending on the value

of the BUSWIDTH pin. The composition of the bits in the CCR

are shown in Table 4.

1.1.1.2 Bus Width and Memory Configurations

The UT80C196KDS external bus can operate as either an 8-bit

or 16-bit multiplexed address/data bus (see figure 2). The value

of bit 1 in the CCR determines the bus operation. A logic low

value on CCR.1 locks the bus controller in 8-bit bus mode. If,

however, CCR.1 is a logic high, then the BUSWIDTH signal is

used to decide the width of the bus. The bus is 16 bits wide when

the BUSWIDTH signal is high, and is 8 bits when the

BUSWIDTH signal is low.

Table 4. Chip Configuration Register

T Bit

Function

7 N/A

N 6 N/A

5 IRC1 - Internal READY Mode Control

E 4 IRC0 - Internal READY Mode Control

3 Address Valid Strobe Select (ALE/ADV)

2 Write Strobe Mode Select (WR and BHE/WRL and WRH)

M 1 Dynamic Bus Width Enable

P 0 Enable Power Down Mode

1.1.2 Reset

To reset the UT80C196KDS, hold the RESET pin low for at

least 16 state times after the power supply is within tolerance

and the oscillator has stabilized. Resets following the power-up

reset may be asserted for at least one state time, and the device

will turn on a pull-down transistor for 16 state times. This

enables the RESET signal to function as the system reset. The

reset state of the external I/O is shown in Table9, and the register

reset values are shown in Table 8.

1.1.3 Instruction Set

The instruction set for the UT80C196KDS is compatible with

the industry standard MCS-96 instruction set used on the

8XC196KDS.

LO Table 5. Memory Map

E Memory Description

V External Memory1

Reserved

EPTS Vectors

DUpper Interrupt Vectors

Begin

02080H

0205EH

02040H

02030H

End

0FFFFH

0207FH

0205DH

0203FH

IN Reserved

Reserved

Chip Configuration Byte

Reserved

02020H

02019H

02018H

02014H

0202FH

0201FH

02018H

02017H

Lower Interrupt Vectors

02000H

02013H

External Memory

00400H

1FFFH

Internal Memory (RAM)

0001AH

003FFH

Special Function Registers

00000H

00019H

Notes:

1.The first instruction read following reset will be from location 2080h. All other external memory can be used as instruction and/or data memory.

3

Share Link: