MAX1836(2002) Просмотр технического описания (PDF) - Maxim Integrated

Номер в каталоге

Компоненты Описание

производитель

MAX1836
(Rev.:2002)

24V Internal Switch, 100% Duty Cycle, Step-Down Converters

Maxim Integrated 

24V Internal Switch, 100% Duty Cycle,

Step-Down Converters

The inductor’s saturation current rating must be greater

than the peak switching current, which is determined

by the switch current limit plus the overshoot due to the

300ns current-sense comparator propagation delay:

IPEAK

=

ILIM

+

(VIN

-

VOUT )

L

300ns

where the switch current-limit (ILIM) is typically 312mA

(MAX1836) or 625mA (MAX1837). Saturation occurs

when the inductor’s magnetic flux density reaches the

maximum level the core can support, and the induc-

tance starts to fall.

Inductor series resistance affects both efficiency and

dropout voltage (see the Input-Output Voltage section).

High series resistance limits the maximum current avail-

able at lower input voltages and increases the dropout

voltage. For optimum performance, select an inductor

with the lowest possible DC resistance that fits in the

allotted dimensions. Typically, the inductor’s series

resistance should be significantly less than that of the

internal P-channel MOSFET’s on-resistance (1.1Ω typ).

Inductors with a ferrite core, or equivalent, are recom-

mended.

The maximum output current of the MAX1836/MAX1837

current-limited converter is limited by the peak inductor

current. For the typical application, the maximum out-

put current is approximately:

IOUT(MAX)

=

1

2

IPEAK

Output Capacitor

Choose the output capacitor to supply the maximum

load current with acceptable voltage ripple. The output

ripple has two components: variations in the charge

stored in the output capacitor with each LX pulse, and

the voltage drop across the capacitor’s equivalent

series resistance (ESR) caused by the current into and

out of the capacitor:

VRIPPLE ≈ VRIPPLE(ESR) + VRIPPLE(C)

The output voltage ripple as a consequence of the ESR

and output capacitance is:

VRIPPLE(ESR) = IPEAKESR

( ) VRIPPLE(C)

=

L

IPEAK - IOUT

2COUTVOUT

2





VIN

VIN - VOUT





where IPEAK is the peak inductor current (see the

Inductor Selection section). These equations are suit-

able for initial capacitor selection, but final values

should be set by testing a prototype or evaluation cir-

cuit. As a general rule, a smaller amount of charge

delivered in each pulse results in less output ripple.

Since the amount of charge delivered in each oscillator

pulse is determined by the inductor value and input

voltage, the voltage ripple increases with larger induc-

tance but decreases with lower input voltages.

With low-cost aluminum electrolytic capacitors, the

ESR-induced ripple can be larger than that caused by

the current into and out of the capacitor. Consequently,

high-quality low-ESR aluminum-electrolytic, tantalum,

polymer, or ceramic filter capacitors are required to

minimize output ripple. Best results at reasonable cost

are typically achieved with an aluminum-electrolytic

capacitor in the 100µF range, in parallel with a 0.1µF

ceramic capacitor.

Input Capacitor

The input filter capacitor reduces peak currents drawn

from the power source and reduces noise and voltage

ripple on the input caused by the circuit’s switching.

The input capacitor must meet the ripple-current

requirement (IRMS) imposed by the switching currents

defined by the following equation:

( ) IRMS = ILOAD

VOUT VIN - VOUT

VIN

For most applications, nontantalum chemistries (ceram-

ic, aluminum, polymer, or OS-CON) are preferred due

to their robustness with high inrush currents typical of

systems with low-impedance battery inputs.

Alternatively, two (or more) smaller-value low-ESR

capacitors can be connected in parallel for lower cost.

Choose an input capacitor that exhibits <+10°C tem-

perature rise at the RMS input current for optimal circuit

longevity.

Diode Selection

The current in the external diode (D1) changes abruptly

from zero to its peak value each time the LX switch

turns off. To avoid excessive losses, the diode must

have a fast turn-on time and a low forward voltage. Use

a diode with an RMS current rating of 0.5A or greater,

and with a breakdown voltage >VIN. Schottky diodes

are preferred. For high-temperature applications,

Schottky diodes may be inadequate due to their high

leakage currents. In such cases, ultra-high-speed sili-

con rectifiers are recommended, although a Schottky

diode with a higher reverse voltage rating can often

provide acceptable performance.

10 ______________________________________________________________________________________

Share Link: