ADM1066 Просмотр технического описания (PDF) - Analog Devices

Номер в каталоге

Компоненты Описание

производитель

ADM1066

Super Sequencer with Margining Control and Auxiliary ADC Inputs

Analog Devices 

ADM1066

Data Sheet

SEQUENCING ENGINE APPLICATION EXAMPLE

The application in this section demonstrates the operation of

the SE. Figure 28 shows how the simple building block of a single

SE state can be used to build a power-up sequence for a three-

supply system. Table 8 lists the PDO outputs for each state in

the same SE implementation. In this system, a good 5 V supply

on VP1 and the VX1 pin held low are the triggers required to

start a power-up sequence. The sequence next turns on the 3.3 V

supply, then the 2.5 V supply (assuming successful turn-on of the

3.3 V supply). When all three supplies have turned on correctly,

the PWRGD state is entered, where the SE remains until a fault

occurs on one of the three supplies or until it is instructed to go

through a power-down sequence by VX1 going high.

Faults are dealt with throughout the power-up sequence on a

case-by-case basis. The following three sections (the Sequence

Detector section, the Monitoring Fault Detector section, and

the Timeout Detector section) describe the individual blocks

and use the sample application shown in Figure 28 to

demonstrate the actions of the state machine.

Sequence Detector

The sequence detector block is used to detect when a step in

a sequence has been completed. It looks for one of the SE inputs

to change state, and is most often used as the gate for successful

progress through a power-up or power-down sequence. A timer

block that is included in this detector can insert delays into a

power-up or power-down sequence, if required. Timer delays

can be set from 10 μs to 400 ms. Figure 27 is a block diagram of

the sequence detector.

VP1

SUPPLY FAULT

DETECTION

SEQUENCE

DETECTOR

VX5

LOGIC INPUT CHANGE

OR FAULT DETECTION

WARNINGS

FORCE FLOW

(UNCONDITIONAL JUMP)

TIMER

INVERT

SELECT

Figure 27. Sequence Detector Block Diagram

Table 8. PDO Outputs for Each State

PDO Outputs

IDLE1 IDLE2

PDO1 = 3V3ON

0

0

PDO2 = 2V5ON

0

0

PDO3 = FAULT

0

0

EN3V3

1

0

0

EN2V5

1

1

0

If a timer delay is specified, the input to the sequence detector

must remain in the defined state for the duration of the timer

delay. If the input changes state during the delay, the timer is reset.

The sequence detector can also help to identify monitoring faults.

In the sample application shown in Figure 28, the FSEL1 and

FSEL2 states first identify which of the VP1, VP2, or VP3 pins

has faulted, and then they take appropriate action.

SEQUENCE

STATES

IDLE1

VX1 = 0

IDLE2

MONITOR FAULT

STATES

VP1 = 1

EN3V3

VP1 = 0

10ms

TIMEOUT

STATES

VP2 = 1

EN2V5

(VP1 + VP2) = 0

20ms

VP3 = 1

DIS3V3

VX1 = 1

(VP1 + VP2 + VP3) = 0

FSEL1

(VP1 +

VP2) = 0

PWRGD

DIS2V5

VP2 = 0

VX1 = 1

VX1 = 1

VP3 = 0

FSEL2

VP1 = 0

VP2 = 0

Figure 28. Sample Application Flow Diagram

DIS3V3

0

1

1

DIS2V5

1

0

1

PWRGD

1

1

0

FSEL1

1

1

1

FSEL2

1

1

1

Rev. F | Page 20 of 36

Share Link: